Abstract:OBJECTIVE To study the effect of bioactive glass (BG) on the dentin bond strength and the microleakage of hybrid layer. METHODS In the study, 30 dentin planes were prepared from the third molars with no caries and equally assigned to the control group, BG group, and sodium trimetaphosphate (STMP)-polyacrylic acid (PAA)-BG group (S-P-BG group), randomly. After etched with 35% phosphoric acid, the dentin planes of BG group were pretreated with 0.5 g/L BG, and the dentin planes of S-P-BG group were pretreated with 5% STMP, 5% PAA and 0.5 g/L BG. No additional pretreatment was done to the dentin planes of control group. Then the dentin planes were bonded using 3M Single Bond 2 adhesive to 3M Z350XT composite resin, and cut into 0.9 mm×0.9 mm column samples, which were stored at 37 ℃ artificial saliva (AS). After 24 hours, 1 month, and 3 months, the microtensile bond strength test was performed. The data were analyzed using one-way ANOVA and LSD method. The morphology of the bond fracture interface was observed with scanning electron microscope. Other 27 teeth were collected and the enamel layer and roots cut off, with the pulp chamber exposed. 0.1% rhodamine B was added to the 3M Single Bond 2 adhesive, and then the adhesive was applied to complete the bonding procedures as above. The teeth were stored in 37 ℃ AS for 24 hours, 1 month, 3 months, and then 0.1% sodium fluorescein solution was placed in the chambers and stained for 1 hour. Confocal laser scanning microscopy was used to observe the interface morphology and microleakage of the hybrid layer. RESULTS At the end of 24 hours and 1 month, there was no significant difference in the microtensile bond strength among the three groups (P>0.05). After 3 months of soaking, the S-P-BG group [(36.91±7.07) MPa] had significantly higher microtensile bond strength than the control group [(32.73±8.06) MPa] (P=0.026); For the control group and the BG group, the microtensile bond strength significantly decreased at the end of 3 months compared with 24 hours (control group: P=0.017, BG group: P=0.01); The microtensile bond strength of S-P-BG group af the end of 3 months had no significant difference in compared with 24 hours [(37.99±7.98) MPa] (P>0.05). Observation of the fracture surface at the 24 hours showed no obvious mineralization in all the three groups. After 1 and 3 months, mineral formation was observed in BG group and S-P-BG group, and no obvious collagen exposure was observed in S-P-BG group. Confocal laser scanning microscopy revealed no obvious differences in the morphology and quantity of the resin tag in the control group, BG group and S-P-BG group. At the end of 24 hours, leakage was found in all the three groups. The microleakage of the control group increased at the end of 3 months, while the microleakage of the BG and S-P-BG groups decreased. CONCLUSION BG pretreatment of dentin bonding interface can induce mineralization at the bonding interface and reduce the microleakage of the hybrid layer; pretreating the dentin bonding interface with STMP, PAA and BG may enhance the maintaining of the dentin bonding durability.

Effect of the use of bromelain associated with bioactive glass-ceramic on dentin/adhesive interface

Effect of natural primer associated to bioactive glass-ceramic on adhesive/dentin interface

Effect of bioactive glass particles on mechanical and adhesion properties of resin cements.

Influence of residues from bioceramic sealer on the bond interface with universal adhesive in different application modes

Influence of bioceramic sealer residues on the adhesion interface with a universal adhesive in the etch-and-rinse strategy, based on the application protocol and evaluation time

Effects of Etching Time and Ethanol Wet Bonding on Bond Strength and Metalloproteinase Activity in Radicular Dentin

Evaluating the effect of poly (amidoamine) treated bioactive glass nanoparticle incorporated in universal adhesive on bonding to artificially induced caries affected dentin

Promoting Bond Durability by a Novel Fabricated Bioactive Dentin Adhesive

Effects of surface treatments of bioactive tricalcium silicate-based restorative material on the bond strength to resin composite

[Effect of Bioactive Glass Pretreatment on the Durability of Dentin Bonding Interface].

Saliva with different concentrations of enzyme with esterolytic activity, and its effect on the immediate and long-term bond strength of adhesive systems to dentin

The effect of long-term water storage on the resin adhesive interface between dentine and glass ceramic

Is it possible for a simultaneous biomodification during acid etching on naturally caries-affected dentin bonding?

30-Month performance of a 10-MDP based universal adhesive system under mechanical and biological perspectives

Impact of functional monomers, bioactive particles, and HEMA, on the adhesive performance of self-etch adhesive systems applied to simulated altered dentin

Effect of experimental dentin etchants on dentin bond strength, metalloproteinase inhibition, and antibiofilm activity

Effect of Bioactive Filler Addition on the Mechanical and Biological Properties of Resin-Modified Glass Ionomer

Effect of phosphoric acid etching and blasting with aluminum oxide on the enamel topography and adhesion of resin composite to intact or abraded enamel

Longitudinal bond strength of a universal adhesive and chemical dentin characterization under different acid etching protocols

Nanoscopic dynamic mechanical analysis of resin-infiltrated dentine, under in vitro chewing and bruxism events

Effect of propolis added to single‐bottle adhesives on water permeation through the hybrid layer