Abstract:OBJECTIVE To study the effect of bioactive glass (BG) on the dentin bond strength and the microleakage of hybrid layer. METHODS In the study, 30 dentin planes were prepared from the third molars with no caries and equally assigned to the control group, BG group, and sodium trimetaphosphate (STMP)-polyacrylic acid (PAA)-BG group (S-P-BG group), randomly. After etched with 35% phosphoric acid, the dentin planes of BG group were pretreated with 0.5 g/L BG, and the dentin planes of S-P-BG group were pretreated with 5% STMP, 5% PAA and 0.5 g/L BG. No additional pretreatment was done to the dentin planes of control group. Then the dentin planes were bonded using 3M Single Bond 2 adhesive to 3M Z350XT composite resin, and cut into 0.9 mm×0.9 mm column samples, which were stored at 37 ℃ artificial saliva (AS). After 24 hours, 1 month, and 3 months, the microtensile bond strength test was performed. The data were analyzed using one-way ANOVA and LSD method. The morphology of the bond fracture interface was observed with scanning electron microscope. Other 27 teeth were collected and the enamel layer and roots cut off, with the pulp chamber exposed. 0.1% rhodamine B was added to the 3M Single Bond 2 adhesive, and then the adhesive was applied to complete the bonding procedures as above. The teeth were stored in 37 ℃ AS for 24 hours, 1 month, 3 months, and then 0.1% sodium fluorescein solution was placed in the chambers and stained for 1 hour. Confocal laser scanning microscopy was used to observe the interface morphology and microleakage of the hybrid layer. RESULTS At the end of 24 hours and 1 month, there was no significant difference in the microtensile bond strength among the three groups (P>0.05). After 3 months of soaking, the S-P-BG group [(36.91±7.07) MPa] had significantly higher microtensile bond strength than the control group [(32.73±8.06) MPa] (P=0.026); For the control group and the BG group, the microtensile bond strength significantly decreased at the end of 3 months compared with 24 hours (control group: P=0.017, BG group: P=0.01); The microtensile bond strength of S-P-BG group af the end of 3 months had no significant difference in compared with 24 hours [(37.99±7.98) MPa] (P>0.05). Observation of the fracture surface at the 24 hours showed no obvious mineralization in all the three groups. After 1 and 3 months, mineral formation was observed in BG group and S-P-BG group, and no obvious collagen exposure was observed in S-P-BG group. Confocal laser scanning microscopy revealed no obvious differences in the morphology and quantity of the resin tag in the control group, BG group and S-P-BG group. At the end of 24 hours, leakage was found in all the three groups. The microleakage of the control group increased at the end of 3 months, while the microleakage of the BG and S-P-BG groups decreased. CONCLUSION BG pretreatment of dentin bonding interface can induce mineralization at the bonding interface and reduce the microleakage of the hybrid layer; pretreating the dentin bonding interface with STMP, PAA and BG may enhance the maintaining of the dentin bonding durability.

Effect of bioactive glass particles on mechanical and adhesion properties of resin cements.

Assessment of Mechanical/Chemical Properties and Cytotoxicity of Resin-Modified Glass Ionomer Cements Containing Sr/F-Bioactive Glass Nanoparticles and Methacrylate Functionalized Polyacids

[Effect of Bioactive Glass Pretreatment on the Durability of Dentin Bonding Interface].

Utilizing an Oxidized Biopolymer to Enhance the Bonding of Glass Ionomer Luting Cement Particles for Improved Physical and Mechanical Properties

Adhesion of new bioactive glass coating

Evaluating the effect of poly (amidoamine) treated bioactive glass nanoparticle incorporated in universal adhesive on bonding to artificially induced caries affected dentin

Effect of Simultaneous Sintering of Bioglass to a Zirconia Core on Properties and Bond Strength

Comparative study of physical-chemical properties of bioactive glass ionomer cement

Novel Bioactive Glass-Modified Hybrid Composite Resin: Mechanical Properties, Biocompatibility, and Antibacterial and Remineralizing Activity

Ion Release and Apatite Formation of Resin Based Pit and Fissure Sealants Containing 45S5 Bioactive Glass

Evaluating the Translucency, Surface Roughness, and Cytotoxicity of a PMMA Acrylic Denture Base Reinforced with Bioactive Glasses

Enamel Surface with Pit and Fissure Sealant Containing 45S5 Bioactive Glass

Effects of novel additives on the mechanical and Biological properties of glass ionomer cement: An in vitro study

Surface characteristics and bacterial adhesion of endodontic cements

Marginal integrity of prototype bioactive glass-doped resin composites in class II cavities

Fabrication and characterization of novel rapid-setting and anti-washout bioactive glass cements for direct pulp capping

Composites bone cements with different viscosities loaded with a bioactive and antibacterial glass

Quantitative study of early-stage transient bacterial adhesion to bioactive glass and glass ceramics: atomic force microscopic observations

Design of Multi-Functional Bio-Safe Dental Resin Composites with Mineralization and Anti-Biofilm Properties

Graphene Nanosheets to Improve Physico-Mechanical Properties of Bioactive Calcium Silicate Cements

Effect of natural primer associated to bioactive glass-ceramic on adhesive/dentin interface