Abstract:Introduction: Geotechnical engineering disasters often result from instability failures in layered and heterogeneous fissured rock masses. However, the key mechanisms governing mechanical properties and crack propagation in these rock masses remain unclear. Methods: This study presents triaxial compression tests on double-layer rock-like specimens composed of limestone and sandstone materials, containing a single fissure, to investigate the effects of fissure angles and positions on the strength and failure modes of these double-layer specimens under varying confining pressure. Results and Discussion: The experimental results reveal that the intact composite rock approaches the strength of sandstone but is deformation-limited by limestone. Under constant confining pressure ( σ 3 = 5 MPa), the fissure angle affects initial crack initiation, and fissure position dictates the failure mode and extent, while increased confining pressure induces overall shear failure in the composite rock, with the failure mode being predominantly influenced by confining pressure. Concerning mechanical deformation, augmenting the fissure angle and confining pressure substantially enhances the elasticity and ductility of the composite rock. Regarding volumetric deformation, the extent of volume shrinkage in the composite rock is influenced by both fissure angle and confining pressure, while volume expansion is influenced by fissure position. Under uniaxial compression, fissured composite rock exhibits the most unstable crack propagation, resulting in early failure. Triaxial compression shows that a higher fissure angle stabilizes crack propagation while confining pressure variation affects stability only when the fissure is in limestone. When the fissure is in sandstone, crack propagation stability remains at its highest. Furthermore, an increase in fissure angle, higher confining pressure, and changes in fissure position from sandstone through the contact interface to limestone contribute to an increasing trend in the peak strength and elastic modulus of the composite rock. Fissure-induced rock degradation is primarily influenced by the fissure angle. These findings are significant for guiding engineering construction and design, providing valuable insights to geotechnical engineers, and enhancing safety in rock engineering projects.

Porosity governs failure in bioconsolidated space bricks

Cracking Behavior and Acoustic Emission Characteristics of Rock Containing a Single Preexisting Flaw

Discrete Element Modeling of Permeability Evolution During Progressive Failure of a Low-Permeable Rock Under Triaxial Compression

Strategies for simultaneous strengthening and toughening via nanoscopic intracrystalline defects in a biogenic ceramic

Phase-field modelling of failure in ceramics with multiscale porosity

Numerical Study of Mechanical Properties and Microcrack Evolution of Double-Layer Composite Rock Specimens with Fissures under Uniaxial Compression

Cracking Evolution and Failure Mechanism of Brittle Rocks Containing Pre-Existing Flaws under Compression-Dominating Stresses: Insight from Numerical Approach

Grain-scale failure mechanism of porous sandstone: An experimental and numerical FDEM study of the Brazilian Tensile Strength test using CT-Scan microstructure

Effects of porosity on the measured fracture energy of brittle materials

Investigation of Multiscale Failure Mechanism of Red Bed Soft Rock Using Grain-Based Finite-Discrete Element Method Combined with X-Ray Micro-computerized Tomography

Continuum modeling of the effect of surface area growth due to crushing and damage on the permeability of granular rocks

Effects of Crack Inclination on Shear Failure of Brittle Geomaterials under Compression

Crack propagation mechanism of rock-like specimens containing non-parallel flaws subjected to internal hydraulic pressure and shear loading

Crack propagation mechanism in rock-like specimens containing intermittent flaws under shear loading

Study on the evolution law and quantitative characterization of micro-crack propagation in the compressive failure process of rocks

Failure modes and mechanical properties of double-layer rock-like composite specimens with a single fissure under triaxial compression

Effect of the porosity on the fracture surface roughness of sintered materials: From anisotropic to isotropic self-affine scaling

Experimental and Theoretical Study on Crack Growth Using Rock-Like Resin Samples Containing Inherent Fissures and its Numerical Assessment

Modeling dynamic crack branching in unsaturated porous media through multi-phase micro-periporomechanics

Study on Microcrack Growth-Based Dynamic Compressive Mechanical Properties in Brittle Rocks