Abstract:Membrane biofouling represents a major challenge ever-present in the practical application of polyamide (PA) thin-film composite (TFC) reverse osmosis (RO) membranes. This work focused on grafting polyacrylamide (PAAm) onto PA-TFC via an in-situ atomic transfer radical polymerization (ATRP) method to improve the biofouling resistance of PA-TFC. The ATRP initiators, isobutyryl bromide (iPB), were introduced into PA matrix using a bifunctional small molecule, 2-bromoisobutyryl bromide (BIBB), added in organic hexane solutions to participate in interfacial polymerization through the condensation reaction with m-phenylenediamine. The successful introduction of iPB was confirmed by membrane surface characterizations, and the iPB density in PA layer was tuned by varying the BIBB concentrations in hexane solutions based on the variation in water permeance and salt rejections of iPB-loaded PA-TFC. The ATRP for the gradual growth of PAAm brush was thus in-situ achieved on the PA-TFC surface from the pre-incorporated iPB groups and the length of PAAm chains was facilely controlled via tuning ATRP polymerization time. The PAAm grafted PA-TFC exhibited a minimum decrement of water permeance and essentially retained salt rejections relative to the un-grafted ones. More importantly, the grafted membranes presented synergistically enhanced anti-adhesion and bacteriostatic performance towards either Gram-negative Escherichia coli (E. coli) or Gram-positive Bacillus subtilis (B. subtilis). Also, the grafted membranes presented a lower final flux decline ratio (FDRf) and higher final flux recovery ratio (FRRf) in relation with the un-grafted membranes in the dynamic bovine serum albumin (BSA) fouling test. Particularly, the membrane grafted with longer PAAm chains from extended grafting time showed better anti-biofouling performance: the sterilization ratio towards E. coli and B. subtilis achieved up to 98.8% and 99.0%, respectively, and FDRf of just 3.7% and FRRf of 97.6% after 3 × 8 h BSA fouling test for the membrane subjected to 2 h ATRP grafting. The PAAm grafting induced greater water wettability of membrane surface and the flexible chain structure of PAAm were proposed to account for the enhanced anti-adhesion and bacteriostasis towards bacteria, which collaboratively led to the improved biofouling resistance.

Antifouling coating of membrane surface with branched poly(2-hydroxyethyl acrylate) brushes via aqueous reversible deactivation radical polymerization

Zwitterion-like, Charge-Balanced Ultrathin Layers on Polymeric Membranes for Antifouling Property.

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Porous poly(vinylidene fluoride) membrane modified with hyperbranched poly(amine-ester)

Porous membranes modified by hyperbranched polymers II.Effect of the arm length of amphiphilic hyperbranched-star polymers on the hydrophilicity and protein resistance of poly(vinylidene fluoride) membranes

Achieving highly effective non-biofouling performance for polypropylene membranes modified by UV-induced surface graft polymerization of two oppositely charged monomers.

Enhancing Membrane Surface Antifouling by Implanting Amphiphilic Polymer Brushes Using a Swelling Induced Entrapment Technique.

Degradable hyperbranched polymer with fouling resistance for antifouling coatings

Tethering Hydrophilic Polymer Brushes Onto PPESK Membranes Via Surface-Initiated Atom Transfer Radical Polymerization

Fouling Control In A Submerged Membrane-Bioreactor By The Membrane Surface Modification

Preparation of antifouling reverse osmosis membrane with polyacrylic acid brushes based on polydopamine coating assisted atom transfer radical polymerization

Free radical graft polymerization of hydroxyethyl methacrylate and acrylic acid on polyetherimide membrane surface via redox system to improve anti-fouling and oil resistance performance

Zwitterionic Modification of Polyurethane Membranes for Enhancing the Anti-Fouling Property.

Biomimetic Surface Modification on Polyacrylonitrile-Based Asymmetric Membranes Via Direct Formation of Phospholipid Moieties

Self-regenerating zwitterionic hyperbranched polymer with tunable degradation for anti-biofouling coatings

PEG-functionalized aliphatic polycarbonate brushes with self-polishing dynamic antifouling properties

Kill–Resist–Renew Trinity: Hyperbranched Polymer with Self-Regenerating Attack and Defense for Antifouling Coatings

Semifluorinated Synergistic Nonfouling/Fouling-Release Surface

Antifouling and Antimicrobial Polymer Membranes Based on Bioinspired Polydopamine and Strong Hydrogen-Bonded Poly(N-Vinyl Pyrrolidone)

Improving the biofouling resistance of polyamide thin-film composite membrane via grafting polyacrylamide brush on the surface by in-situ atomic transfer radical polymerization

Zwitterionic Sulfobetaine-Grafted Poly(vinylidene Fluoride) Membrane Surface with Stably Anti-Protein-fouling Performance Via a Two-Step Surface Polymerization