Abstract:Over the last few decades, the demand for lightweight constructions has been increased continuously for several industrial applications, like automotive and ship building, to reduce the weight of vessels in order to minimize the CO2 emissions as a result of a lower fuel consumption. Lightweight construction is almost applied for ship applications, especially for yachts, which are designed by using aluminum for the deck constructions and steel for the ship hull. For joining these parts, a high-power laser welding process shall be developed. However, the welding of these dissimilar materials is associated with great challenges, due to the different physical properties and the formation of hard and brittle intermetallic phases, which may influence negatively the properties of the weld seam. The quality of dissimilar joints depends strongly on the mixture ratio between the molten amount of steel and aluminum. However, the mixture ratio varies over the weld seam length due to a high dynamic of the keyhole resulted by welding of this material combination. Furthermore, different batches of materials and varied sheet thicknesses t may influence the mixture ratio. In this study, a high-power laser welding process is developed with in-process control of the penetration depth tP by analyzing the spectral process emissions for dissimilar lap joints of aluminum alloy EN AW-6082 (t = 8 mm) and steel S355 (t = 5–7 mm). In the context of these investigations, an increase of occurring cracks within the weld seam and ejections of molten material with increasing penetration depth tP can be observed. To achieve a relative high joint strength, the penetration depth tP must be kept constant at a value of 1.4 mm. In case of varied batch of material, thickness t of the used sheets, welding speed vS, and leap of the steel sheet thickness t, the penetration depth tP requested cannot be achieved. Using the in-process control of the penetration depth tP, the weld seam quality remains almost constantly over the weld seam length, as shown in visual inspections, metallographic analyses, profiles of the penetration depth tP, and tensile shear testing. Among other things, the appearance of ejections of molten material can be avoided by using the in-process control of the penetration depth tP.

Systematic approach to improve overlap laser welding of AA5052-H32 with dissimilar thickness by evaluation of mechanical performance, undercut, and welding penetration

Weldability improvement by wobbling technique in high power density laser welding of two aluminum alloys: Al-5052 and Al-6061

Minimizing defects and controlling the morphology of laser welded aluminum alloys using power modulation-based laser beam oscillation

Effects of Laser Oscillating Frequency on Energy Distribution, Molten Pool Morphology and Grain Structure of AA6061/AA5182 Aluminum Alloys Lap Welding

Effect of oscillation parameters on adjustable-ring mode (ARM) laser beam welding of aluminum alloys

Influence of Scanning Paths on the Weld Pool Behavior, Microstructure, and Mechanical Property of AA2060 Al-Li Alloy Joints by Laser Beam Oscillation Welding

Experimental investigations on mechanical properties of AA6061-T6 aluminum alloy joined by laser welding using digital image correlation

Microstructure and Properties of Multilayer 5052 Aluminum Alloy Sheet by Laser Welding

Effect of swinging laser on porosity, microstructure, and mechanical properties of laser welded aluminum alloy joints with different lap forms

Interfacial microstructure and mechanical properties of laser-welded 6061Al/AISI304 dissimilar lap joints via beam oscillation

Optimizing 3D Laser Foil Printing Parameters for AA 6061: Numerical and Experimental Analysis

The role of filler wire and scanning strategy in laser welding of difficult-to-weld aluminum alloys

Microstructural, Porosity and Mechanical Properties of Lap Joint Laser Welding for 5182 and 6061 Dissimilar Aluminum Alloys under Different Place Configurations

Laser dissimilar welding of Al/Mg lap-joint with Ti interlayer through optimized 8-shaped beam oscillation

Investigations on in-process control of penetration depth for high-power laser welding of thick steel-aluminum joints

Microscopic and Mechanical Properties Characterization of Laser Beam Welded 5754 to 6063 Aluminum Alloys

Improving mechanical properties of quasi-continuous-wave laser beam welded 7075 aluminum alloy through microstructural refinement and homogenization of the fusion zone

Influence of oscillation parameters on energy distributions and dynamic behaviors during laser welding of aluminum alloy T-joints assisted with solder patch

Optimization of process parameters in friction stir welding of dissimilar aluminum alloys (AA6061–T6 and AA5052–H32)

Investigations on improving the properties of laser beam welded thick dissimilar joints of steel and aluminum by using filler material

Study on the Influence of Weld Spacing on the Tensile Strength of Laser Double-Pass Reciprocating Welding of DP780/6061-T6 Dissimilar Metals