Abstract:The availability of such vast land so that the transfer to the agricultural sector which is large enough to be difficult to stem along with technological advances in agriculture will allow the farmers' businesses to be more enthusiastic in the hope that better growth in agricultural production will be achieved. On the other hand, it will reduce losses/loss of yields due to the production process so that there is an improvement in the application of harvesting and postharvest technology which seems to be a prospective source of production growth. In its development, local farmers in Merauke using the rice drying method still use the old method, namely drying in the hot sun in an open field. If the weather is favorable, the drying process will not take up to 14 days and sometimes if the field or yard is not enough, someone will use the services of someone else to dry it. This also raises complaints because the costs that must be incurred by farmers will be even greater. The research developed is to design a rice grain dryer where the characteristics or drying method is a dryer with hot air/gas pressure produced from the combustion process in the furnace. The objectives of this research are to design a dryer installation that can dry grain effectively, efficiently and economically with the Pressure Flow Heat Forced Convection method as an air heater in the drying room, determine the percentage of grain moisture content with free convection and forced convection with drying time, and calculate the efficiency of the dryer installation with forced convection as a hot air sucker from the combustion furnace to the drying chamber and compare the results. The research was appointed based on the problems that exist in the community, especially in the Kurik district, Wonorejo village, Merauke Regency, Papua. This research is also a manifestation of the vision of Musamus University, which is to become a reference for empowering independent communities based on local wisdom through downstream research. The results showed that for testing the weight loss of grain, the best results were obtained between the 540th and 620th minutes with a weight of less than 15 g. So from 12 tons of wet grain that was dried after a drying process for 12 hours, the amount of water that evaporated for a 3 kg sample was 0.875 kg so that the dry grain weight was 2.125 kg. Total drying of 12 tons of grain to 10.5 tons. The total evaporation of water vapor in the grain is 0.875 x 12000 kg = 10500 kg (10.5 tons). This shows that the heat used for the rice grain drying process can be used optimally where the efficiency of the grain dryer installation is 71%.

Experiment and Modeling of Rice Winnowing: Granular Segregation Method in Ancient Traditions

Design of Grain Dryer using Pressure the Flow of Air Heat Forced Convection Method

Motion Simulation and Experimental Analysis of Rice Seedling on Vibrating Board of Ordered Rice Seedling Thrower

Optimization of airflow cylinder sieve for threshed rice separation using CFD-DEM

Effect of the rotational speeds of the screw conveyor and milling roller on the behaviour of grain flows in the connected chamber of a vertical “conveying-milling” rice mill

DEM Study of the Size-Induced Segregation Dynamics of a Ternary-Size Granular Mixture in the Rolling-Regime Rotating Drum

Near-Infrared Identification of the Dimmest X-ray Sources on the Galactic Plane with the ESO/NTT SOFI Camera

Effect of drying and milling modes on the quality of white rice of an Indonesian long grain rice cultivar

Segregation of Granular Mixtures in a Rotating Drum

Study on Separation of the Tuber-Soil Binary Mixture Based on Vibration and Airflow Coupling

Separation characteristics of white rice in an indented cylinder separator with a baffle

Characteristics of Rice Fractionated by Rice Kernel Thickness and Its Application

Optimization of Roasted Green Tea Winnowing Via Fluid–Solid Interaction Experiments and Simulations

CFD Simulation Analysis and Experimental Verification of Hybrid Rice Pollen Diffusion Process

Microscopic Model for Granular Stratification and Segregation

DEM investigation of the axial dispersion behavior of a binary mixture in the rotating drum

MATHEMATICAL MODELING OF THE PROCESS OF MOVEMENT OF GRAIN MATERIAL ON THE SURFACE OF A SIEVE OF A VIBRATING PNEUMATIC PULSE SEPARATOR

Modeling the process of grain separation by density in a combined vibro-pneumatic and air-gravity unit

Design and Experimental Analysis of a Stirring Device for a Pneumatic Precision Rice Seed Metering Device

Modeling of extraction of silica rendemen husk rice (Oryza sativa l.) by microwave extraction assisted (MAE) using response surface methodology (RSM)

Making artificial rice from sorghum flour, corn flour and cassava starch by using mini extruder