Abstract:Kelvin's model is widely used to simulate the dynamic characteristic of a resilient mat under a slab track. To develop an effective calculation model for a resilient mat using a solid element, a three-parameter viscoelasticity model (3PVM) was employed. With the help of the user-defined material mechanical behavior, the proposed model was implemented in software ABAQUS. To validate the model, a laboratory test was performed on a slab track with a resilient mat. Then, a finite element model of the track-tunnel-soil system was built. The calculation results using the 3PVM was compared with those using Kelvin's model and the test results. The results indicate that the 3PVM can better reflect the dynamic characteristics of resilient mat than Kelvin's model, especially over 10 Hz. Compared with the test results, the 3PVM has an average error of 2.7 dB and a max error of 7.9 dB at 5 Hz.

What problem does this paper attempt to address?

The problem this paper attempts to address is: how to more accurately simulate the dynamic characteristics of the elastic layer in Floating Slab Track (FST). Specifically, the paper proposes a method based on the Three-Parameter Viscoelastic Model (3PVM) to replace the traditional Kelvin model, thereby better reflecting the dynamic behavior of the elastic layer at high frequencies. ### Background With the development of urban rail transit, the issue of vibrations caused by trains in tunnels and buildings has increasingly drawn attention. These environmental issues may affect nearby residents, the long-term preservation of historical buildings, and the operation of precision instruments. To control the vibrations caused by trains, various vibration reduction measures can be taken, among which Floating Slab Track (FST) has proven to be one of the most effective solutions. FST effectively reduces vibrations by installing springs or elastic layers under the track slab, forming a mass-spring system. ### Existing Problems Although the Kelvin model is widely used to simulate the dynamic characteristics of steel springs, it is difficult to accurately simulate the vibration characteristics of the elastic layer using the Kelvin model due to its special viscoelastic properties. Therefore, the paper proposes a new method, using the Three-Parameter Viscoelastic Model (3PVM) to simulate the dynamic characteristics of the elastic layer. ### Solution 1. **Model Development**: The paper proposes a modeling method based on 3PVM and implements this model in ABAQUS software through user-defined material mechanical behavior. 2. **Experimental Validation**: Dynamic tests of the floating slab track were conducted in the laboratory to verify the accuracy of the model. 3. **Results Comparison**: The calculation results of the 3PVM model were compared with those of the Kelvin model and experimental results. The results show that the 3PVM model can better reflect the dynamic characteristics of the elastic layer at high frequencies. ### Main Conclusions - The 3PVM model can more accurately simulate the dynamic characteristics of the elastic layer in the frequency range above 10 Hz compared to the Kelvin model. - Compared with experimental results, the average error of the 3PVM model at 5 Hz is 2.7 dB, and the maximum error is 7.9 dB. Through this research, the paper provides a new method for the accurate modeling of the elastic layer in Floating Slab Track, which helps to further optimize the vibration reduction effect of rail transit systems.

Study on Modelling Method of Resilient Mat Used under Floating Slab Track

Three-dimensional Finite Element Simulation on Moving Load Induced Track Response over Stiffness-varied Base

Finite Element Modelling of Two-way RC Slabs with Varying Modelling Choices

Dynamic Coefficient of Slab Track System on Subgrade under High-Speed Trains

Modeling of Unsaturated Granular Materials in Flexible Pavements

Development of a Modulus of Subgrade Reaction Model to Improve Slab-Base Interface Bond Sensitivity

Dynamic Analysis of a Slab Track on the Poroelastic Soil Subjected to Moving Loads

Simulation of vertical dynamic vehicle–track interaction using a three-dimensional slab track model

From Material to Field Test: An Improved Under Sleeper Pad Model

Evaluation Method of the Vibration Reduction Effect Considering the Real Load- and Frequency-Dependent Stiffness of Slab-Track Mats

A Theoretical Investigation on Influences of Slab Tracks on Vertical Dynamic Responses of Railway Viaducts

Optimum Analysis of Vibration Reduction Performance for Floating Slab Track Based on Shear Hinge

A frequency and amplitude dependent model of rail pads for the dynamic analysis of train-track interaction

Three-Dimensional Simulation of Track on Poroelastic Half-Space Vibrations Due to A Moving Point Load

Modeling Slab Track for Vehicle –Track-Coupled Dynamics Analysis Using Spline Function Method

Vibration Reduction in Ballasted Track Using Ballast Mat: Numerical and Experimental Evaluation by Wheelset Drop Test

Theoretical modelling of a vehicle-slab track coupled dynamics system considering longitudinal vibrations and interface interactions

DYNAMIC RESPONSE ANALYSIS OF TRACK SYSTEM AND UNDERGROUND RAILWAY TUNNEL IN SATURATED SOIL SUBJECTED TO A MOVING TRAIN LOAD

Finite element simulation and falling ball impact model for cement concrete pavement considering void under slab

Damping Characteristics of Ballast Mat on the Rail Joint

Technical Note: Three-dimensional analyses of dynamic responses of track-ground system subjected to a moving train load