Abstract:<p>Biocompatible β Ti-alloys with high strength and low modulus are of interest for additive manufacturing of biomedical implants. In this study, a metastable β Ti-12Mo-6Zr-2Fe (TMZF) alloy with highly dense structure was successfully fabricated by laser powder bed fusion (LPBF) from low-cost elemental powders. The applied different scanning strategies (simple and chess scan), and post heat treatment can regulate both the texture and secondary phases. The formation of strong {100}< 001 > texture leads to the low elastic modulus of TMZF alloys, while nano-sized α" phases induce significantly strengthening effect. The as-fabricated TMZF alloy via simple scanning strategy shows considerably high strength due to the high density of α", ω phases and sessile dislocations, but it is brittle owing to the presence of ω phase. The TMZF alloy, manufactured using chess scanning strategy, possessed high yield strength of 1,026 MPa, low modulus of 85.7 GPa and good ductility of 12.7%. This results from its unique hierarchical microstructure containing α" phases, heterogeneous grains and the formation of {100}< 001 > texture. After solution heat treatment, the specimens exhibit stronger {100} < 001 > texture, hence lower modulus of 70.9 GPa. High yield strength of 943 MPa was maintained due to the formation of plate-like α" precipitates. The TMZF alloy fabricated by in-situ alloying based LPBF demonstrates comparable strength to that of Ti-6Al-4V alloy, but much lower elastic modulus, suggesting that it could be a potential candidate for some implant applications.</p>

Selective laser melting of biomedical Ti15Mo alloy: A proper combination of strength and ductility under the effects of multiple mechanisms

Study of superior strength in Ti15Mo alloy manufactured using selective laser melting

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

In-situ Tailoring Mechanical Properties of Metastable Ti15Mo Alloy Produced by Selective Laser Melting

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Controlling the microstructure and mechanical properties of a metastable β titanium alloy by selective laser melting

Achieving Strength-Ductility Synergy of Laser Powder Bed Fusion Ti–6.5Al–2Zr–1Mo–1V Alloy by Regulating Laser Power

Selective laser melting of titanium alloy with 50 wt% tantalum: Microstructure and mechanical properties

Cost-affordable, biomedical Ti-5Fe alloy developed using elemental powders and laser in-situ alloying additive manufacturing

Selective Laser Melting Enabled Additive Manufacturing of Ti-22Al-25Nb Intermetallic: Excellent Combination of Strength and Ductility, and Unique Microstructural Features Associated

Investigation on the Microstructure and Mechanical Properties of the Ti-Ta Alloy with Unmelted Ta Particles by Laser Powder Bed Fusion

Heat-treatment induced microstructural evolution and enhanced mechanical property of selective laser melted near β Ti-5Al-5Mo-5 V-3Cr-1Zr alloy

Effect of scanning strategies on the microstructure and mechanical properties of Ti–15Mo alloy fabricated by selective laser melting

Microstructure and Mechanical Properties of An Ultrahigh-strength Titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb Prepared Using Laser Directed Energy Deposition and Forging: A Comparative Study

Selective Laser Melting of a Novel Al-Si-Fe-Mn-Ni Alloy with Superior Mechanical Properties at Both Room and Elevated Temperatures: Influence of Processing Parameters and Heat Treatment

Mechanical Properties and Microstructure of DMLS Ti6Al4V Alloy Dedicated to Biomedical Applications

Ti6Al4V Alloy Remelting by Modulation Laser: Deep Penetration, High Compactness and Metallurgical Bonding with Matrix

Selective laser melted near-beta titanium alloy Ti-5Al-5Mo-5V-1Cr-1Fe: Microstructure and mechanical properties

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

A high strength and low modulus metastable β Ti-12Mo-6Zr-2Fe alloy fabricated by laser powder bed fusion in-situ alloying