Abstract:Structural evolution of two propylene 1-butene random copolymer (iPPBu) films with different initial crystalline morphology during uniaxial deformation were investigated by synchrotron wide-angle and small-angle X-ray scattering (WAXS/SAXS), Fourier-transform infrared (FTIR) spectroscopy. The iPPBu with α crystal crystallized via mesophase exhibits a nodular morphology, while melt-crystallized iPPBu exhibits a characteristic spherulitic structure. The initial crystalline morphology has been found to exert influence on the structural evolution of the samples, including cavitation, orientation behavior of molecular chains in crystalline and amorphous phases, the occurrence of mesophase, and reduction in crystallinity, etc. Compared with the iPPBu with spherulitic morphology, no obvious cavitation was observed around the yield point in iPPBu with nodular morphology. Moreover, the variation rate of crystallinity with respect to draw ratio is smaller in the iPPBu with nodular morphology. A plausible reason for the phenomenon is that the iPPBu with nodular morphology has the lower lateral extension of crystallites. The onset draw ratio (λ onset) of α-crystal-to-mesophase transition in sample with nodular morphology is larger than that in the sample with spherulitic morphology. The molecular chains tend to be aligned perpendicular to the stretching direction in iPPBu with spherulitic morphology around yield point. This is attributed to the bending and separation of the lamellae with the normal parallel to the tensile direction. However, this phenomenon is not observed in the iPPBu with nodular morphology. In the strain-hardening regime, the strain hardening modulus G p of iPPBu with nodular morphology is higher than that of iPPBu with spherulitic morphology, which results from the more cross-linking points and more tie chains in highly oriented the amorphous phase of the former. A deformation mechanism is proposed to understand the role played by the initial morphology of iPPBu based on the crystal transition, variation in crystallinity, cavitation, and orientation.

Three representative types of WAXD/SAXS patterns to establish the bimodal structure concept of stacked lamellae in isotactic polypropylene spherulites

Microstructure characterization in a single isotactic polypropylene spherulite by synchrotron microfocus wide angle X-ray scattering

Structure and morphology development in syndiotactic polypropylene during isothermal crystallization and subsequent melting

Probing the Early Stages of Melt Crystallization in Polypropylene by Simultaneous Small- and Wide-Angle X-ray Scattering and Laser Light Scattering

Crystallization and multiple melting behavior of oriented thick lamellae in isotactic polypropylene

Influence of Molecular Weight on the Nucleation and Growth of Different Crystal Forms in Isotactic Polypropylene: In Situ Synchrotron Microfocus X-Ray Scattering Combined with Fast-Scanning Chip Calorimetry Investigations

Structural Analysis of Poly(Butylene Adipate) Banded Spherulites from Their Biodegradation Behavior

Morphology Development During Isothermal Crystallization. I. Isotactic and Atactic Polypropylene Blends

A Time-Resolved SAXS Study on the Crystalline Morphology of Long-Term Stored Isotactic Polypropylene

Flow and Pressure Jointly Induced Ultrahigh Melting Temperature Spherulites with Oriented Thick Lamellae in Isotactic Polypropylene

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

Epitaxial Crystallization and Oriented Structure of Linear Low-Density Polyethylene/Isotactic Polypropylene Blends Obtained Via Dynamic Packing Injection Molding

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Real Time Synchrotron SAXS and WAXS Investigations on Temperature Related Deformation and Transitions of Β-Ipp with Uniaxial Stretching

Conformation transition and crystalline phase variation of long chain branched isotactic polypropylenes (LCB-iPP)

Further Understanding on the Three Domains of Isotactic Polypropylene by Investigating the Crystalline Morphologies Evolution after Treatment at Different Domains

Conformational ordering on the growth front of isotactic polypropylene spherulite

Tensile deformation mechanism of propylene-1-butene random copolymer: The role of initial crystalline morphology

Relationship between molecular structure, crystallization behavior, and mechanical properties of long chain branching polypropylene

Co- existing morphologies of lamellae and double arrays of cylinders by A<sub>1</sub>BA<sub>2</sub>C tetrablock terpolymer

Competition of shearing and cavitation effects on the deformation behavior of isotactic polypropylene during stretching