Abstract:Fretting wear is one of the main factors restricting the fastener service reliability for the high -temperature titanium alloys. Enhancing the high -temperature fretting wear resistance of titanium alloys with laser cladding coatings is an effective method. Thus, in this work, a self-lubricating composite coating was designed and fabricated on the surface of TC21 titanium alloy with laser cladding. Special attentions were made to the effect of the fractions of the hard and self-lubricating phases on high -temperature fretting resistance. In addition, the contribution of laser cladding power was also concerned. The primary phases of the self-lubricating composite coatings are alpha-Co, CaF2, WC, TiC and Cr23C6, and the reasons for the formation of TiC and Cr23C6 are investigated from a thermodynamic point. The prepared composite coatings are dense and uniform. The crystallographic characteristics and the volume fractions of the hard phases (WC, TiC and Cr23C6) and self-lubricating phase (CaF2) were revealed, and the effect of grain size on the coating properties was analyzed. The hardness of the coatings were all maintained around 700 HV0.2, which was significantly higher than that of the substrate. The composite coating significantly improves the friction and wear resistance at 500 celcius. The hard phase was also found to be the most resistant to friction and wear. The frictional performance of the coating gets better when the hard phase and the self-lubricating phase increase. However, the hard phase contributes more to the hightemperature friction and wear resistance than the self-lubricating phase and the wear volume is 1/40 that of substrate. For the laser cladding power, the higher power can lead to a higher fraction of CaF2 but a lower fraction of hard phase, causing a decline in COF but an increase in wear volume. The wear mechanisms of the coating and the substrate were analyzed, the subsurface stress distribution state of the wear scars were further analyzed. The current results present new insights on the anti -wear design strategy to the composite coatings consist of hard and self-lubricating phase.

High-temperature fretting wear behavior and microstructure stability of a laser-cladding Ti-Al-C-N composite coating meditated by variable cycle conditions

Variable cycle fretting conditions meditated wear behavior and mechanism in a self-lubricating composite coating on TC21 titanium alloy substrate

Enhancing High-Temperature Fretting Wear Resistance of TC21 Titanium Alloys by Laser Cladding Self-Lubricating Composite Coatings

Effect of Laser Remelting on Microstructure Evolution and High-Temperature Fretting Wear Resistance in a Laser-Cladding Self-Lubricating Composite Coating on Titanium Alloy Substrate

Fretting Wear Resistance at Ambient and Elevated Temperatures of 316 Stainless Steel Improved by Laser Cladding with Co-based Alloy/wc/caf2 Composite Coating

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

Fretting wear resistance at ambient and elevated temperatures of 316 stainless steel improved by laser cladding with Co-based alloy/WC/CaF 2 composite coating

Microstructure and Wear Resistance of a Composite Coating Prepared by Laser Alloying with Ni-Coated Graphite on Ti-6Al-4V Alloy

Development and Characterization of Laser Clad High Temperature Self-Lubricating Wear Resistant Composite Coatings on Ti–6Al–4V Alloy

Enhancing High-Temperature Fretting Wear Resistance of Ti-64 Alloy by Laser Cladding Fecralmoxnby High Entropy Alloy Coatings

Microstructure and Tribological Behavior of Laser Cladding TiAlSi Composite Coatings Reinforced by Alumina–titania Ceramics on Ti–6Al–4V Alloys

Microstructure and Tribological Properties of Laser Surface Alloyed TiN and TiC Reinforced Composite Coatings on TiAl Intermetallic Alloy

Microstructure and Wear Resistance of Laser Cladding Ti-Al-Ni-Si Composite Coatings

Microstructure and wear resistance of laser clad TiC reinforced FeAl intermetallic matrix composite coatings

Preparation and Study on Fretting Tribological Behavior of Composite Lubrication Structure on the Titanium Alloy Surface

Microstructure and tribological properties of laser in-situ synthesized Ti3Al composite coating on Ti-6Al-4V

Microstructure and properties of Ti–Al–C composite coatings prepared by laser cladding

Revealing Fretting Wear Resistance Mechanism under Liquid Lead-Bismuth Eutectic of Cr-Al-C Composite Coatings Fabricated by Laser Cladding

Microstructure and Wear Resistance of Ti6Al4V Titanium Alloy Laser-Clad Ni60/WC Composite Coating

Fretting Wear Behaviors of APS AT40 Coating and Al2O3/AT40 Composite Coating on TC6 Alloy

Study on Wear Resistance of Ti-6Al-4V Alloy Composite Coating Prepared by Laser Alloying