Abstract:Statement of problem: Three Co-Cr alloy types (Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W) have been commonly used in the fabrication of dental prostheses. These alloys can be manufactured using either conventional casting or selective laser melting (SLM) techniques. Nevertheless, research that directly compares these materials and/or manufacturing processes in terms of their microstructural and mechanical characteristics is sparse. Purpose: The purpose of this in vitro study was to conduct microstructural and mechanical analysis via X-ray interpretation, optical microscopy, scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), image analysis, X-ray diffraction (XRD), instrumented indentation testing (IIT), and 3-point bending testing to characterize Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W alloys produced through conventional casting and SLM. Material and methods: Six Co-Cr-based alloys were analyzed and divided into 3 types based on their elemental composition (Co-Cr-Mo, Co-Cr-W, and Co-Cr-Mo-W). Additionally, each group was categorized based on the manufacturing process used (casting or SLM). X-ray scans were used to assess porosity. The microstructures of the specimens were assessed through SEM/EDS examination and XRD analysis. IIT was used to determine the Martens hardness (HM) and elastic index (ηIT), while the elastic modulus (E) was estimated through the 3-point bending test. The mechanical properties were statistically analyzed using 2-way analysis of variance (ANOVA) and the Tukey multiple comparison post hoc test, with alloy type and manufacturing process as discriminating variables (α=.05). Results: All cast groups exhibited gross porosity, while no pores or other flaws were found in the SLM groups. Based on the XRD results, the crystalline structure of all Co-Cr specimens consisted of the face-centered cubic γ phase (γ-fcc), along with the hexagonal close-packed ε phase (ε-hcp) and Cr23C6 carbide. Different microstructures were identified between the cast and SLM alloys. Significant differences were identified for the mean standard deviation HM (ranging from 2601 ±94 N/mm2 to 3633 ±61 N/mm2) and mean ±standard deviation ηIT (ranging from 16.8 ±0.3% to 20.9 ±0.3%) among alloys prepared by the same manufacturing process, while all SLM alloys had statistically higher HM and ηIT results than their cast counterparts (P<.05). No statistically significant differences were identified for the mean ±standard deviation Eb (ranging from 170 ±25 GPa to 244 ±36 GPa) among the groups prepared with the same manufacturing process (P>.05), but the SLM alloys had significantly higher results (P<.05) than the cast alloys. Conclusions: In general, the manufacturing procedure significantly affected the porosity, microstructure, and mechanical properties of the tested Co-Cr alloys. SLM decreased the internal porosity, provided a uniform microstructure, and improved the mechanical properties for all the tested alloy types.

Investigating the effect of select alloying elements in additively manufactured Co-Cr alloy for dental prosthetics

Wear Resistance and Biocompatibility of Co-Cr Dental Alloys Fabricated with CAST and SLM Techniques

Additive Manufacturing of Cobalt-Based Dental Alloys: Analysis of Microstructure and Physicomechanical Properties

In vitro biocompatibility of CoCrMo dental alloys fabricated by selective laser melting

Comparative Analysis of Mechanical Properties and Metal-Ceramic Bond Strength of Co-Cr Dental Alloy Fabricated by Different Manufacturing Processes

Microstructural and mechanical characterization of six Co-Cr alloys made by conventional casting and selective laser melting

Comparative analysis of the microstructures and mechanical properties of Co-Cr dental alloys fabricated by different methods

Influence of Precipitation Hardening on the Mechanical Properties of Co-Cr-Mo and Co-Cr-W-Mo Dental Alloys

Impact of minor alloying with C and Si on the precipitation behavior and mechanical properties of N-doped Co-Cr alloy dental castings

Microstructural Characterization, Mechanical Properties, and Corrosion Resistance of Dental Co-Cr-Mo-W Alloys Manufactured by Selective Laser Melting

Cobalt chromium alloys in fixed prosthodontics: Investigations of mechanical properties and microstructure

Microstructure-Properties Characterization of Selective Laser Melted Biomedical Co-28Cr-6Mo Alloy

Preparation and Properties of Co–Cr Alloy Denture by Selective Laser Melting

Study on the Surface of Cobalt-Chromium Dental Alloys and Their Behavior in Oral Cavity as Cast Materials

Improving biotribological properties and corrosion resistance of CoCrMo alloy via a Cr-GLC nanocomposite film in simulated body fluids

Assessment of precipitation behavior in dental castings of a Co-Cr-Mo alloy

Mechanical Properties and Metal-Ceramic Bond Strength of Co-Cr Alloy Manufactured by Selective Laser Melting

Microstructure enhanced biocompatibility in laser additively manufactured CoCrMo biomedical alloy

Structural characterization of biomedical Co-Cr-Mo components produced by direct metal laser sintering

Selective Laser Melting Technique of Co-Cr Dental Alloys: A Review of Structure and Properties and Comparative Analysis with Other Available Techniques

Process optimization and electrochemical behavior of CoCrMo alloy fabricated by selective laser meltingbased on response surface method