Abstract:The interactions among thermal history, plastic deformation and residual stresses in the friction stir welding (FSW) process under different welding parameters have been widely considered a crucial issue and still not fully understood. In the present study, a novel three-dimensional fully coupled thermo-mechanical finite element (FE) model based on coupled Eulerian-Lagrangian approach (CEL) has been developed to simulate the FSW process of aluminium alloy AA 6082-T6 and to analyse the thermo-mechanical interaction mechanisms under different welding conditions. The numerical model successfully simulates the plunge, dwell, and welding steps in FSW and captures the evolution of temperature, plastic deformation, and residual stresses in the welded joint. The obtained results were validated by experimental testing with observed cross-weld thermal history, optical macrography and residual stress measurement using the neutron diffraction technique. The results reveal that the tool rotation speed governs the temperature evolution; the peak temperature increased from 740 to 850 °K when the tool rotation speed rose from 800 to 1100 rpm. The rotational speed also affected the plastic deformation, material flow, and the volume of material being stirred during the welding process. Higher plastic deformation is formed in the stirring zone by increasing the tool angular velocity. This behaviour led to an increase in the stirring effect of the welding tool, reduction of the tunnel defect size and enhancing the quality of weldments. The distribution of residual stresses in different zones of the FSW joints has been found to have an M-shaped profile. A significant tensile residual stress is characterised in the edge of the nugget zone in both longitudinal and transverse directions, balanced by compressive stresses in the thermo-mechanically affected zone, heat-affected zone and base metal. The presented FE modelling provides a reliable insight into the effects of the welding parameters on the weld quality of FSW joints and process optimisation with minimised experimental trials.

Enhancing Friction Stir Welding Performance for 2017AA Alloy through Cooling with Mediterranean Seawater

Effects of friction stir welding on corrosion and mechanical properties of AA6063 in sea water

Effects of Underwater Friction Stir Welding Heat Generation on Residual Stress of AA6068-T6 Aluminum Alloy

Numerical and experimental study of underwater friction stir welding of 1Cr11Ni2W2MoV heat-resistant stainless steel

Cooling-assist friction stir welding: A case study on AA6068 aluminum alloy and copper joint

Optimization of process parameters of friction stir welded joints of marine grade AA 5083

Tailoring the Microstructure of an AA5754 Aluminum Alloy by Tuning the Combination of Heat Treatment, Friction Stir Welding, and Cold Rolling

Assessment of the Corrosion Behavior of Friction-Stir-Welded Dissimilar Aluminum Alloys

Friction stir welding of a rapidly solidified thin-strip continuous cast AA5182 Al–Mg alloy: analysis of microstructure evolution, mechanical properties, and corrosion resistance

Improving mechanical properties of FSWed AA6061-T6 joint by controlling microstructural changes through utilization of stationary shoulder tool in presence of Al2O3 nanoparticles and external cooling

Cooling Environment Effect on the Microstructure and Mechanical Properties of Friction Stir-Welded Joints

Improving the corrosion resistance of friction stir welding joint of 7050 Al alloy via optimizing the process route

Underwater dissimilar friction stir lap welding of aluminum alloy and CFRTP

Durability of Single Lap Friction Stir Welded Joints between S355-J0 Steel and AA5083 Aluminum Alloy–Mechanical Tests

Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy

Heat generation, plastic deformation and residual stresses in friction stir welding of aluminium alloy

Underwater friction stir welding of ultrafine-grained laminated composites produced through accumulative roll bonding process

Influence of multiple friction stir welding passes on the microstructure and mechanical properties of AA2024 age-hardened aluminum alloy

Enhancing Mechanical Characteristics of 6061-T6 with 5083-H111 Aluminum Alloy Dissimilar Weldments: A New Pin Tool Design for Friction Stir Welding (FSW)

A novel technique to examine the corrosion resistance of FSW dissimilar aluminium alloys under three different corrosion solutions

Friction Stir Welding of AZ31B Magnesium Alloy with 6061-T6 Aluminum Alloy: Influence of Processing Parameters on Microstructure and Mechanical Properties