Abstract:As an efficient heat transfer device, two-phase loop thermosyphon (TPLT) has a broad application prospect in many engineering fields, and its internal gas-liquid phase change and flow characteristics are the key factors affecting the heat transfer performance. In order to get a better thermal design and performance, it is necessary to clarify the heat transfer mechanism of the TPLT, especially under the con-dition of high filling ratio. In this study, the visualization experiment was combined with the CFD method to study the heat transfer and flow characteristics of TPLT. Due to the strong coupling relationship among the boiling process and the condensate process, the Lee model is optimized, and the relationship between saturation temperature and local pressure, and the parameter of subcooling degree in the Lee model were both introduced to accurately simulate the phase change process. Results shows that the optimized model has good prediction performance for the heat and mass transfer simulation of the loop thermosyphon. The two-phase flow in the loop thermosyphon changes from slug flow to churn flow with the increase of heating power at low filling ratio (50%), while the bubble size decreases and the number of bubbles increases with the increase of heating power (20W-80W) at high filling ratio (70%). The heat transfer mechanism before and after model optimization has changed, from saturated flow boiling to subcooled flow boiling at high filling ratios. At low filling ratio (50%), the fluid in heating section is saturated state, and the flow velocity at the bottom of the loop is low (0.018m/s). At high filling ratio (70%), the fluid in the heating section is supercooled state, and the fluid flow velocity at the bottom of the loop is high (0.171m/s). This indicates that the heat transfer mechanism of the loop thermosyphon at low filling ratio was saturated pool boiling, and the filmwise condensation occurs in the condensation section. However, the heat transfer mechanism is subcooled flow boiling at high filling ratio, and the gas-liquid two phases in the condensation section are in a mixed state.(c) 2022 Elsevier Ltd. All rights reserved.

Optimization Design of Closed-Loop Thermosyphons: Experimentation and Computational Fluid Dynamics Modeling

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

CFD Modelling and Visual Analysis of Heat Transfer and Flow Pattern in a Vertical Two-Phase Closed Thermosyphon for Moderate-Temperature Application

Experimental and numerical analysis of a nanofluidic thermosyphon heat exchanger

Experimental Study of an Aluminum Based Three-Dimensional Thermosyphon Heat Sink with Microscale Enhancement Structure

Experimental investigation on the thermal performance of a novel thermosyphon heat pipe with truncated cone for heat recovery systems

Experimental and theoretical analysis of a closed loop two-phase thermosiphon under various states for latent heat storage

Experimental Study on the Thermal Characteristics of a 3D Thermosyphon Heat Sink

Thermal performance analysis of heat pipe heat exchanger for effective waste heat recovery

Thermodynamic Optimization of the Recuperative Heat Exchanger for Joule–Thomson Cryocoolers Using Response Surface Methodology

Experimental and CFD investigation on the thermal performance of two phase closed thermosyphons: Effect of corrugated evaporator

Advanced Thermal Management System Based on a Novel Flat Evaporator Loop Heat Pipe with High-Efficiency Condenser for Electronic Cooling

Experimental Investigation of the Thermal Performance of Heat Pipes with Double-Ended Heating and Middle-Cooling

Single/multi-objective optimization and comparative analysis of liquid-metal heat pipe

Experimental Study on Heat Transfer Characteristics of Thermosyphon Radiator

Numerical investigation of the thermal performance of a loop thermosyphon considering dynamic condensation mass transfer time relaxation parameter

Performance assessment of a geometrical modification on thermosyphon heat pipe with the assistance of novel convergent-divergent truncated cones for energy recovery systems

Investigation of Heat Transfer and Flow Characteristics in Two-Phase Loop Thermosyphon by Visualization Experiments and CFD Simulations

Experimental research on boiling heat transfer mechanism of a pump-driven loop thermosiphon for R134a coolant

Experimental and Numerical Investigation on a CO2 Loop Thermosyphon for Free Cooling of Data Centers

Numerical Study and Parametric Analysis of Thermo-Hydraulic Behavior in a Flat Loop Heat Pipe at System Scale