Abstract:Purpose Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens. Design/methodology/approach This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature. Findings It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process. Originality/value 316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

The Effects of Manufacturing Techniques on the Mechanical Performance of an Auxetic Structure Manufactured by FFF and MJF Processes

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Experimental Characterisation and Finite Element Modelling of Polyamide-12 Fabricated via Multi Jet Fusion

Supportless Lattice Structure for Additive Manufacturing of Functional Products and the Evaluation of Its Mechanical Property at Variable Strain Rates

Thermal, Tensile and Fatigue Behaviors of the PA6, Short Carbon Fiber-Reinforced PA6, and Continuous Glass Fiber-Reinforced PA6 Materials in Fused Filament Fabrication (FFF)

Effect of design parameters on auxetic behavior and stiffness of additively manufactured 316L stainless steel

The Effect of Design and Fabrication Parameters on the Mechanical Properties of 3D Re-Entrant Honeycomb Auxetic Structures

Effects of build positions on the thermal history, crystallization, and mechanical properties of polyamide 12 parts printed by Multi Jet Fusion

Experimental and Numerical Analysis of a Novel Assembled Auxetic Structure with Two-Stage Programmable Mechanical Properties

Effects of testing speed on the tensile and mode I fracture behavior of specimens printed through the Fused Deposition Modeling technique

Effect of build direction on tension-tension low cycle fatigue behavior of polyamide 12 parts printed by Multi Jet Fusion

Experimental Study of the Tensile Behavior of Structures Obtained by FDM 3D Printing Process

In Situ X‐Ray Tomography of Sintered Metal Fiber Felts Exhibiting Auxetic Effect under Tension and Compression

Process–Structure–Property Relationship Development in Large-Format Additive Manufacturing: Fiber Alignment and Ultimate Tensile Strength

Additive manufacturing of 316L stainless-steel structures using fused filament fabrication technology: mechanical and geometric properties

The effect of printing parameters on the mechanical properties of fiber-reinforced PA6 matrix composites in material extrusion-based additive manufacturing

Microstructure and compression performance of novel AlSi10Mg composite auxetic structures fabricated by additive manufacturing

Reduction of Process Induced Porosity for Ultrafuse 316L through Parameter Optimization of Creality Ender 3 V2 and Makerbot Method X

Effects of fused filament fabrication (FFF) process parameters on tensile and flexural properties of ABS/PLA multi-material

Effects of Printing Temperature and Filling Percentage on the Mechanical Behavior of Fused Deposition Molding Technology Components for 3D Printing

Process parameter sensitivity of the energy absorbing properties of additively manufactured metallic cellular materials