Abstract:The increasing emissions of construction waste and industrial by-products have caused a serious burden on the environment. The shortage of natural coarse aggregate (NCA) and river sand provides the impetus for the reuse of solid waste. This research provides a cleaner option for the production of recycled aggregate concrete (RAC) from industrial by-product molybdenum tailings (MTs). MTs are used as alternative material to river sand (10%, 30%, 50%, 70% and 100%). Three types of concrete natural aggregate concrete (NAC), RAC, and MTs recycled aggregate concrete (MTs-RAC) were prepared. Firstly, the mechanical properties of the specimens were tested, including compressive strength (fcu) and splitting tensile strength (fst), and the digital image correlation (DIC) system was used to evaluate the strain field distribution. Then, the freeze-thaw (F-T) cycle corrosion resistance of concrete was evaluated. Subsequently, the pore structure was visualized and quantitatively analyzed based on industrial CT technology. The evolution of corrosion resistance of MTs-RAC was confirmed by microstructure. Finally, the economic efficiency factor (EEF) and environmental impact (EI) were evaluated. The experimental results showed that the appropriate amount of MTs significantly improved the pore structure and mechanical properties of RAC, and the fcu of RAC with a 50% MTs replacement rate increased by a maximum of 14.4%, which could achieve the same mechanical properties as NAC. However, the combination of excess MTs and recycled coarse aggregate (RCA) increases the porosity of concrete. The F-T cycle resistance of RAC decreased with the increase of MTs replacement rate. The increase in the proportion of large pores (>10 mm3) is the main factor leading to the destruction of F-T cycles. On balance, the replacement rate of MTs for use in RAC should not exceed 50% in salt lakes and cold regions. The results are helpful to understand the influence mechanism of MTs on RAC performance and provide the theoretical basis for the application of MTs in RAC.

Comparison on micromechanical properties of interfacial transition zone in concrete with iron ore tailings or crushed gravel as aggregate

The Mechanical Properties and Microstructure of Tailing Recycled Aggregate Concrete

Integrated Interface Parameters of Recycled Aggregate Concrete

Nano- and Microscopic Investigation on the Strengthening Mechanism of ITZs Using Waste Glass Powder in Modeled Aggregate Concrete

Properties characterization of interfacial transition zone of recycled concrete for reducing the resource waste and environmental pollution

Microstructure Of Interface Transition Zone In High Performance Recycled Aggregate Concrete

Damage evaluation of concrete using iron ore tailings as aggregates under uniaxial cyclic compression

Impact of Interfacial Transition Zone on Concrete Mechanical Properties: A Comparative Analysis of Multiphase Inclusion Theory and Numerical Simulations

Roles of enhanced ITZ in improving the mechanical properties of concrete prepared with different types of recycled aggregates

Utilization of molybdenum tailings as fine aggregate in recycled aggregate concrete

Iron ore tailings, phosphate slags, and lithium slags as ternary supplementary cementitious materials for concrete: Study on compression strength and microstructure

The Influence of Iron Tailings Powder on the Properties on the Performances of Cement Concrete with Machine-Made Sand

Experimental Investigation on the Performance of Cement Mortar by Partial Replacement of the Standard Sands with Sulfide-Contained Iron Tailings

Offsetting strength loss in concrete via ITZ enhancement: From the perspective of utilizing new alternative aggregate

An Approach to Effectively Improve the Interfacial Bonding of Paste–limestone by Incorporating Different Nanomaterials

Unlocking the potential of iron ore tailings in controlled low-strength material: Feasibility, performance, and evaluation

A review of the interfacial transition zones in concrete: Identification, physical characteristics, and mechanical properties

Sustainable assessment and synergism of ceramic powder and steel slag in iron ore tailings-based concrete

Micromechanical analysis of interfacial transition zone in alkali-activated fly ash-slag concrete

A different type of congenital lumbar hernia associated with the lumbocostovertebral syndrome.

Strengthening Effect of Graphene Oxide on Mechanical Properties of Interface Transition Zone of Recycled Concrete