Abstract:The methanation process, or Sabatier process, allows carbon dioxide and carbon monoxide to be hydrogenated into methane, which can be subsequently injected (once the gas grid specifications have been respected) into the gas network infrastructures already present in Europe. This process can be effectively adopted to convert captured CO 2 streams from power plants or hard to abate plants by using green hydrogen from renewable-driven water electrolysis. The technical aspects of concern in the methanation process are certainly the strong exothermicity of the process, with consequent possible generation of hotspots along the entire catalyst bed and the management of reaction heat through thermal recovery. These peculiar aspects influence the choice of construction materials and geometry of the methanation reactor, operating parameters, cooling system, type of catalyst/support and the initial conditions of the feed. In particular, the generation of hotspots influences the local kinetic reaction in the methanation reactor, the diffusional limits of hydrogen and carbon dioxide inside the catalyst and the chemical-physical characteristics of the catalyst bed. The present work reports a first scale-up of the Sabatier process, developed in Aspen Plus simulation environment, with the following characteristics: reactor size to process 925 Nm 3 /h, (750 hydrogen and 175 carbon dioxide), at 15 bar and 250 °C. After the implementation in the steady state, a dynamic simulation is performed to carry out a transient study of the entire plant. In particular, the attention is focused on the variation in the hydrogen load, produced by electrolysis from the energy surplus from renewable sources. Considering the variable nature of the power flow supplied to the electrolyser and therefore any shutdown and cold start-up phases of this equipment, the following load variation scenarios for the Power to Gas (PtG) system are simulated: −5%, +5% and −30 % molar flow rate of incoming hydrogen, compared to steady conditions used in the preliminary design of the equipment. The study highlights how the cooled reactor configuration is more performing and characterized by a lower number of reactors in series (2 reactors) when compared to the adiabatic configuration (5 reactors). Furthermore, in the cooled reactor configuration the control system is able to respond more quickly to load variations compared to that designed for the adiabatic case, although the latter is mostly adopted from the industrial viewpoint due to temperature control issues. Moreover, the control system manages to respond to load variations by bringing the values of interest (gas grid residual concentration of hydrogen and carbon dioxide, Wobbe index) into the target intervals.

Two-zone convective reformer for the decentralized production of H 2 /syngas from biomethane

An Innovative Micro-Channel Catalyst Support with a Micro-Porous Surface for Hydrogen Production Via Methanol Steam Reforming

Development of Pure Hydrogen Generation System Based on Methanol Steam Reforming and Pd Membrane

Hydrogen production and geometry optimization of ethanol steam reforming combining water gas shift reaction in a crossflow membrane tube reactor

Standalone ethanol micro-reformer integrated on silicon technology for onboard production of hydrogen-rich gas

Optimization of Small-Scale Hydrogen Production with Membrane Reactors

Membrane reformer technology for sustainable hydrogen production from hydrocarbon feedstocks

Bi-reforming of Methane in a Carbon Deposit-Free Plasmatron with High Operational Adaptability

Absorption-Enhanced Methanol Steam Reforming for Low-Temperature Hydrogen Production with Carbon Capture

Continuous Production of Hydrogen from Sorption-Enhanced Steam Methane Reforming in Two Parallel Fixed-Bed Reactors Operated in a Cyclic Manner

Numerical Evaluation of Heat Transfer and Conversion Efficiency by Tube Design and Flow Configuration for a Compact Steam-Methane Reformer

Power-to-Gas: Process analysis and control strategies for dynamic catalytic methanation system

Design and Operational Considerations of Packed-Bed Membrane Reactor for Distributed Hydrogen Production by Methane Steam Reforming

Carbon Utilization Through Power to Gas and Oxyfuel Combustion Hybridization with Recycled CO2: Design and Preliminary Results

Hydrogen Production via Steam Reforming: A Critical Analysis of MR and RMM Technologies

A Novel 2-Reactor Chemical Looping System for Hydrogen Production with Biogas as the Feedstock: Process Simulation and Comparison with Conventional Reforming Processes

Numerical investigation of hydrogen production via methane steam reforming in a novel packed bed reactor integrated with diverging tube

Double-Tube Reactor Design and Process Optimization for On-Site Steam Methane Reforming Processes

A new design of catalytic tube reactor for hydrogen production from ethanol steam reforming

Configuration of coupling methanol steam reforming over Cu-based catalyst in a synthetic palladium membrane for one-step high purity hydrogen production

Standalone micro-reformer for on-board hydrogen production from dimethyl ether