Abstract:The steel plate shear walls (SPSWs) have been proven effective in reinforced concrete frames (RCFs) as a lateral force‐resistant structure. Despite of advancements, accurately predicting the ultimate shear capacity of RCFs with SPSWs remains challenging using current simplified models. Additionally, the flexural capacity design procedure for the boundary elements (beams and columns) in previous studies of RCF‐SPSWs involved intricate iterative procedures, hindering its widespread implementation. To address the two issues, this paper investigates the pushover responses and the plate‐frame interaction (PFI) of an RCF‐SPSWs system using theoretical and numerical methods. There are three main contributions. First, a theoretical model of ultimate shear capacity for RCF‐SPSWs is proposed, which can also be used to predict shear contributions of boundary frames in RCF‐SPSWs. Calculation errors for ultimate shear capacity of RCF‐SPSWs and shear contribution from the boundary frame are only 3.7% and 6.7% respectively, which are reduced dramatically compared with the traditional model. A simplified schematic diagram for the global collapse mechanism (uniform distribution of plastic hinges within a structure) of RCF‐SPSWs is developed to facilitate the calculation of internal work and reaction forces. Secondly, a flexural capacity design method for the boundary elements to avoid in‐span plastic hinges is proposed. The proposed method enables the achievement of direct estimation of the flexural demands that could trigger a global collapse mechanism, all without intricate iterative procedures. The applicability of current assumptions for the design of steel boundary frame in RCF‐SPSWs system is discussed, and engineering suggestions are provided to ensure safer and more economic designs. Comparison results confirmed the applicability of the proposed design method, which can be adopted to achieve the global collapse mechanism for RCF‐SPSW system. Thirdly, impacts of yielding panel actions on the flexural capacity of boundary elements of RCF‐SPSWs are clarified. Comparison results demonstrated that adding SPSWs to an RCF alters the axial force on boundary elements and significantly impacts the flexural capacity. A design suggestion is made to emphasize the importance of avoiding the balanced failure of boundary elements. The proposed theoretical model can be used to economize the cross‐section of boundary elements in RCF‐SPSWs system under seismic loads due to accurate prediction of their shear contribution; the proposed flexural capacity design method can achieve a global collapse mechanism, and thus the structural safety and energy dissipation capacity are improved; moreover, the building design efficiency is also improved due to avoidance of intricate iterative procedures.

A multi-modal-analysis-based simplified seismic design method for high-rise frame-steel plate shear wall dual structures

A SIMPLIFIED ANALYTICAL PROCEDURE FOR SEISMIC ANALYSIS OF TIMBER LIGHT-FRAME SHEAR WALLS

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

Subassemblage Tests on Seismic Behavior of Double-Corrugated-plate Shear Walls

Energy-Balance-Based Plastic Design and Seismic Fragility Analysis of Steel Plate Shear Wall Coupled with Steel Side Columns

Experiment and Numerical Analysis of Multi-Story Coupled Steel Plate Shear Wall with Weak-Axis Connections

Performance-Based Seismic Design of Corrugated Steel Plate Shear Walls

Theoretical models of key parameters for performance‐based seismic design of new partially connected steel plate shear wall with vertical square tube stiffeners

A two-level performance-based plastic design method for multi-story steel frames with double-yielding systems

Damage indices and fragility assessment of coupled low-yield-point steel plate shear walls

On the Seismic Evaluation of Steel Frames Laterally Braced with Perforated Steel Plate Shear Walls Considering Semi-Rigid Connections

Performance-based-plastic-design of damage-control steel MRFs equipped with self-centring energy dissipation bays

Simplified Analytical Model and Shaking Table Test Validation for Seismic Analysis of Mid-Rise Cold-Formed Steel Composite Shear Wall Building

Assessment of the Seismic Performance and the Base Shear Contribution Ratios of the RC Wall-frame Dual System Considering Soil–Structure Interaction

Theoretical model of ultimate shear capacity and flexural capacity design method of boundary elements for reinforced concrete frames with steel plate shear walls

Mechanical performance and design method of two-side-connected SPSW reinforced on free edges

Comparative seismic analysis of frames with shape memory alloy slip friction dampers

Performance-based seismic design method for disc spring-based self-centering viscous dissipative braced steel frame

Seismic responses analysis of multi-story suspended floors system

Seismic performance assessment of steel frame infilled with prefabricated wood shear walls

Seismic design and parametric study of steel modular frames with distributed seismic resistance