Abstract:The measurement of airborne particles with sizes below 3 nm is critical, as it helps the understanding of atmospheric nucleation and elucidates important particle synthesis mechanisms in the gas phase. Condensation particle counters (CPCs) have been widely used to measure the concentration of aerosols. However, it is challenging for the CPCs to measure particles below 3 nm due to the insufficient activation of these particles via vapor condensation. Methods have been proposed to increase the saturation ratio of the condensing vapor to promote the detection efficiency of sub-3 nm particles in the CPCs. Different working fluids also make a considerable impact on particle detection. Given the various types of parameters and the wide range of values these parameters can take, modeling studies are needed in searching for the optimal operating conditions of a CPC.In this work, we simulated the sub-3 nm particle activation and growth in a laminar flow CPC using COMSOL Multiphysics®, which has the advantages of simulating complex flow conditions and interfacing with post-processing software such as MATLAB. Our simulation incorporates the influence of temperature-dependent air and working fluid properties on particle activation and the impact of latent heat and non-continuum effects on droplet growth. Following the method introduced by Iida, Stolzenburg and McMurry (2009), particle activation is optimized for a given working fluid and condenser temperature by adjusting the saturator temperature to achieve a homogeneous nucleation rate of 1 s−1. The results, characterized by Dkel,0 (largest particle size that cannot be activated) and Dkel,50 (particle size activated with 50% efficiency), were compared against the analytical Graetz model used in Stolzenburg (1988). Our COMSOL simulations show that glycerine, diethylene glycol, ethylene glycol, 2-aminoethanol, and dimethyl phthalate are the best five working fluids achieving the smallest Dkel,50 among 45 commonly used solvents. The Dkel,50 values simulated by COMSOL under a condenser temperature of 10 °C for the five working fluids are 1.56, 1.88, 1.92, 1.98, and 2.10 nm, respectively, while the values simulated by the analytical Graetz solution differ slightly from 0.4% to 0.7%. The results demonstrate excellent agreement between these two simulation methods. For the five best working fluids activating the same 2.1 nm particles, the droplets can grow to sizes detectable by a second-stage CPC. The sensitivity of the COMSOL solution to the inlet condition and the form of convective diffusion equations is investigated. We also discussed the effect of CPC operating conditions, such as the condenser geometry and flow conditions, on particle activation for optimizing the performance of the CPC in detecting sub-3 nm particles.

Mapping the performance of a versatile water-based condensation particle counter (vWCPC) with numerical simulation and experimental study

On Water Condensation Particle Counters and their Applicability to Field Measurements

Scanning Supersaturation Condensation Particle Counter Applied As a Nano-Ccn Counter for Size-Resolved Analysis of the Hygroscopicity and Chemical Composition of Nanoparticles

Characteristics of Scanning Flow Condensation Particle Counter (SFCPC): A Rapid Approach for Retrieving Hygroscopicity and Chemical Composition of Sub-10 Nm Aerosol Particles

Mixing State of Atmospheric Particles over the North China Plain

Liquid water content measurement with SEA multi-element sensor in CARDC icing wind tunnel: Calibration and performance

Numerical Modeling of Droplet Aerosol Coagulation, Condensation/Evaporation and Deposition Processes

Characterization of Three New Condensation Particle Counters for Sub-3 Nm Particle Detection: ADI Versatile Water CPC, TSI 3777 Nano Enhancer and Boosted TSI 3010

Modification and laboratory evaluation of a TSI ultrafine condensation particle counter (Model 3776) for airborne measurements

A convertible condensation particle counter using alcohol or water as the working fluid

Direct Measurement of Aerosol Liquid Water Content: A Case Study in Summer in Nanjing, China

Performance evaluation of the national air quality testing services V2000 Condensation Particle Counter

Retrieval of Cloud Condensation Nuclei Number Concentration Profiles from Lidar Extinction and Backscatter Data

The condensation particle counter battery (CPCB): A new tool to investigate the activation properties of nanoparticles

Optimizing the activation efficiency of sub-3 nm particles in a laminar flow condensation particle counter: Model simulation

Characterization of three new condensation particle counters for sub-3 nm particle detection during the Helsinki CPC workshop: the ADI versatile water CPC, TSI 3777 nano enhancer and boosted TSI 3010

Improving New Particle Formation Simulation by Coupling a Volatility-Basis Set (VBS) Organic Aerosol Module in NAQPMS+APM

Improving Aerosol Characterization Using an Optical Particle Counter Coupled with a Quartz Crystal Microbalance with an Integrated Microheater

Method to Retrieve Cloud Condensation Nuclei Number Concentrations Using Lidar Measurements

Development of Aerosol Sample Introduction Interface Coupled with ICP-MS for Direct Introduction and Quantitative Online Monitoring of Environmental Aerosol

Numerical Simulation of Clouds and Precipitation Depending on Different Relationships Between Aerosol and Cloud Droplet Spectral Dispersion