Abstract:Bioretention systems have become a leading infiltration-based Low Impact Development (LID) practice to reduce urban stormwater runoff volumes and peak flows. Although these systems have performed well in many site-scale field studies, modeling of bioretention systems has received less attention. Additional studies are needed which calibrate various models to field measurements to investigate and optimize the performance of individual LID practices and effectively scale local interventions to the watershed. DRAINMOD-Urban has been successfully applied to bioretention at the site-scale due to its advanced soil–water accounting using the soil–water characteristic curve and its ability to explicitly model underdrains and internal water storage (IWS) zones. At the same time, the U.S. EPA Stormwater Management Model (SWMM) has become one of the most widely used urban drainage models. The latest version, SWMM5, included dedicated LID modules including a routine for bioretention modeling.In this study, DRAINMOD-Urban and the SWMM LID module were compared through detailed analysis of the internal processes of each model as well as through model calibration and output investigation. The objective was to identify the strengths and weaknesses of each model and compare the performance of both models to a single bioretention cell. Both SWMM and DRAINMOD-Urban were evaluated in calibrated and uncalibrated scenarios since urban drainage models often remain uncalibrated for planning scenario analysis. Following calibration, DRAINMOD-Urban was superior for replicating drainage hydrographs (NSE = 0.60) while SWMM produced better overflow hydrographs (NSE = 0.57). Specifically, SWMM often output a maximum drainage rate that caused rectangular drainage hydrographs, but DRAINMOD-Urban was better able to match the shape of measured drainage hydrographs. While the DRAINMOD-Urban model output was in good agreement with measured drainage and overflow event volumes when calibrated (drainage NSE = 0.83, overflow NSE = 0.57–0.66), SWMM was closer to measured volumes even when uncalibrated (drainage NSE = 0.70–0.93, overflow NSE = 0.59–0.81). This study improved existing knowledge of the SWMM LID module by calibrating to field-collected data from a single bioretention cell for the first time in literature. Furthermore, the results of this study indicate an opportunity for model coupling that could combine the strengths and weaknesses of each model and improve bioretention cell modeling.

Large‐scale physical facility and experimental dataset for the validation of urban drainage models

Hydraulic, wash-off and sediment transport experiments in a full-scale urban drainage physical model

Impact of Spatial Variation and Uncertainty of Rainfall Intensity on Urban Flooding Assessment

Urban pluvial flood modelling in the absence of sewer drainage network data: A physics-based approach

Simulation of the hydraulic performance of highway filter drains through laboratory models and stormwater management tools

Calibration and validation of SWMM model in two urban catchments in Athens , Greece

Urban Pluvial Flood Modeling by Coupling Raster-Based Two-Dimensional Hydrodynamic Model and SWMM

Benchmarking 2d Hydraulic Models for Urban Flooding

Rainfall-Runoff Simulations to Assess the Potential of SuDS for Mitigating Flooding in Highly Urbanized Catchments

Development of a Geospatial Data-Based Methodology for Stormwater Management in Urban Areas Using Freely-Available Software

SIMULATION OF HYDROLOGICAL CYCLE IN AN URBANIZED CATCHMENT AND EFFECT EVALUATION OF INFILTRATION FACILITIES

Modeling bioretention hydrology: Quantifying the performance of DRAINMOD-Urban and the SWMM LID module

Experimental study of rainwater grate blocking and submergence of outfall on drainage network capacity

A two-dimensional hydrodynamic urban flood model based on equivalent drainage of manholes

Urban Drainage Efficiency Evaluation and Flood Simulation Using Integrated SWMM and Terrain Structural Analysis.

Assessment of inlet efficiency through a 3D simulation: numerical and experimental comparison

Data-driven methodological approach for modeling rainfall-induced infiltration effects on combined sewer overflow in urban catchments

The Value of Aggregated City Scale Models to Rapidly Assess SuDS in Combined Sewer Systems

Simulation of Hydraulic Structures in 2D High-Resolution Urban Flood Modeling

Urban Stormwater and Sewerage Modelling: An Approach for Peak Runoff and Volume Assessment

Modelling urban rainfall-runoff responses using an experimental, two-tiered physical modelling environment [Abstract]