Abstract:Flexible pressure sensors have attracted intense attention because of their widespread applications in electronic skin, human–machine interfaces, and healthcare monitoring. Conductive porous structures are always utilized as active layers to improve the sensor sensitivities. However, flexible pressure sensors derived from traditional foaming techniques have limited structure designability. Besides, random pore distribution causes difference in structure and signal repeatability between different samples even in one batch, therefore limiting the batch production capabilities. Herein, we introduce a structure designable lattice structure pressure sensor (LPS) produced by bottom-up digital light processing (DLP) 3D printing technique, which is capable of efficiently producing 55 high fidelity lattice structure models in 30 min. The LPS shows high sensitivity (1.02 kPa<sup>–1</sup>) with superior linearity over a wide pressure range (0.7 Pa to 160 kPa). By adjusting the design parameters such as lattice type and layer thickness, the electrical sensitivities and mechanical properties of LPS can be accurately controlled. In addition, the LPS endures up to 60000 compression cycles (at 10 kPa) without any obvious electrical signal degradation. This benefits from the firm carbon nanotubes (CNTs) coating derived from high-energy ultrasonic probe and the subsequent thermal curing process of UV-heat dual-curing photocurable resin. For practical applications, the LPS is used for real time pulse monitoring, voice recognition and Morse code communication. Furthermore, the LPS is also integrated to make a flexible 4 × 4 sensor arrays for detecting spatial pressure distribution and a flexible insole for foot pressure monitoring.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21407?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21407</a>.Comparison of additive manufacturing techniques for preparation of porous materials for flexible electronics; optical photographs of the lattice structure green model after DLP 3D printing and after CNT coating; SEM images of bare TPU substrate and CNT-coated sample; cross-section SEM image of CNT-coated sample; tensile stress-strain curves of 3D printed pure TPU compared to PDMS and Ecoflex 00-10; optical and SEM images of conductive fabric interdigital electrode; optical photograph of LPS under a compression and release cycle at a compression rate of 0.1 mm/s; optical images of the LPSs with three lattice types ("A", "D" and "E") at various applied pressure; compressive stress–strain curves of LPSs with 5 types of lattice structure; cyclic compression test under 40 kPa at different frequencies; SEM images of LPS sample after 60 000 cycles compression test at 10 kPa with a frequency of 0.5 Hz; current response of LPS attached on the throat when saying "Printing" and "What's up"; SEM images of the surface morphology of papers with different roughness (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21407/suppl_file/am0c21407_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

All Digital Light Processing‐3D Printing of Flexible Sensor

Flexible Pressure Sensor with Micro-Structure Arrays Based on PDMS and PEDOT:PSS/PUD&CNTs Composite Film with 3D Printing

High-Performance Flexible Piezoresistive Pressure Sensor Printed with 3D Microstructures

Recent Progress on Three-dimensional Printing Processes to Fabricate Flexible Tactile Sensors

3D printing wide detection range and high sensitivity flexible pressure sensor and its applications

3D Printing of Flexible Strain Sensor Based on MWCNTs/Flexible Resin Composite

3D Printing of Highly Sensitive and Large-Measurement-Range Flexible Pressure Sensors with a Positive Piezoresistive Effect

Facile Fabrication of Flexible Pressure Sensor with Programmable Lattice Structure

3D-Printable Carbon Nanotubes-Based Composite for Flexible Piezoresistive Sensors

Flexible capacitive pressure sensor based on electrically assisted micro-nanoimprinting

Highly Sensitive Flexible Piezoresistive Sensor with 3D Conductive Network

Electrohydrodynamic (EHD) inkjet printing flexible pressure sensors with a multilayer structure and periodically patterned Ag nanoparticles

A stretchable flexible strain sensor with high sensitivity and fast response fabricated by embedded 3D printing of the hybrid polydimethylsiloxane/conductive carbon paste composites

Design and Fabrication of Flexible Capacitive Sensor With Cellular Structured Dielectric Layer via 3D Printing

Flexible Piezoresistive Sensor with the Microarray Structure Based on Self-Assembly of Multi-Walled Carbon Nanotubes

Flexible Micropillar Array for Pressure Sensing in High Density Using Image Sensor

Structural Design and DLP 3D Printing Preparation of High Strain Stable Flexible Pressure Sensors

3D Printing of Flexible Strain Sensor Array Based on UV‐Curable Multiwalled Carbon Nanotube/Elastomer Composite

Additive Fabrication of Pressure Sensitive Material for Flexible Pressure Sensor and Its Characteristics

A Stretchable Pressure Sensor with Interlinked Interfaces Prepared by a Template-Free Process

Broad detection range of flexible capacitive sensor with 3D printed interwoven hollow dual-structured dielectric layer