Abstract:In this study, a distributed optical fiber sensor was used for strain monitoring and installation adjustment of a satellite–rocket connection device under a preload. The distributed optical fiber sensor was installed on both the tape and the satellite docking frame, utilizing OFDR (Optical Frequency Domain Reflectometry) based on Backward Rayleigh scattering strain demodulation methods to precisely measure the strain distribution of both components when subjected to a preload. In order to deal with the uneven stress of the belt in the process of preloading, a finite element analysis was performed to obtain the strain distribution of the belt under preloading. The strain monitoring results of the optical fiber and strain gauge were compared, and the strain trend of the finite element simulation results was verified. Finally, the measured strain data were adopted to assist the installation and adjustment of the satellite–rocket connection device to achieve a uniform distribution of the preload. The experimental results showed that the standard deviation of strain at each position of the tape was reduced after adjustment. This study provides guidance for the installation of satellite–rocket connection devices.

What problem does this paper attempt to address?

The problem that this paper attempts to solve is the strain monitoring and installation adjustment during the pre - loading process of the satellite - rocket connection device. Specifically, the author is concerned with how to ensure the uniform force on the satellite - rocket connection device during pre - loading, so as to improve its reliability and safety. ### Problem Background The Satellite - Rocket Connection Device is a key component, which is responsible for reliably connecting the satellite and the rocket during the rocket launch process and achieving reliable separation on the predetermined orbit. In order to ensure the reliability of this connection, a preload force is usually applied to the connection device. However, the traditional mechanical loading methods have problems such as low labor efficiency and unstable quality, especially it is difficult to ensure uniformity when multi - point synchronous loading. ### Main Problems 1. **Insufficient Strain Monitoring**: The traditional strain gauge monitoring method has problems such as few measurement points, possible loss of strain information, and inability to synchronously monitor the satellite frame. 2. **Difficult Installation and Adjustment**: During the pre - loading process, it is difficult to monitor and adjust the strain distribution of the clamp band and the satellite frame in real - time to ensure the uniform application of the preload force. ### Solutions In order to solve the above problems, this research proposes a method based on Distributed Optical Fiber Sensors (DOFS) for real - time monitoring and adjustment of the strain distribution of the satellite - rocket connection device during the pre - loading process. Specific methods include: - **Optical Fiber Sensor Deployment**: Install distributed optical fiber sensors on the clamp band and the satellite frame, and use the Optical Frequency Domain Reflectometry (OFDR) technology to accurately measure the strain distribution of the clamp band and the satellite frame under pre - loading through the backward Rayleigh scattering strain demodulation method. - **Finite Element Analysis**: Conduct finite element analysis to obtain the strain distribution of the band during the pre - loading process and verify the experimental results. - **Strain Data Comparison and Adjustment**: Compare the monitoring results of the optical fiber sensor and the strain gauge, verify the trend of the finite element simulation results, and use the measured strain data to assist in installation and adjustment to achieve the uniform distribution of the preload force. ### Experimental Results The experimental results show that after adjustment, the strain standard deviation at each position of the band is significantly reduced, achieving the purpose of uniformly distributing the preload force. This provides guidance for the installation of the satellite - rocket connection device and improves its reliability and safety. ### Key Formulas The formulas involved in this paper are mainly used to describe the principle of optical fiber sensing, for example: \[ \Delta\lambda = K_T \Delta T + K_\epsilon \Delta \epsilon \] where: - \(\Delta\lambda\) is the wavelength change; - \(K_T\) is the temperature sensitivity coefficient, with the default value of \(6.45\times 10^{-6}\, \text{℃}^{-1}\); - \(K_\epsilon\) is the strain sensitivity coefficient, with the default value of \(0.780\); - \(\Delta T\) is the temperature change; - \(\Delta \epsilon\) is the strain change. These formulas help to explain how the optical fiber sensor measures the changes in strain and temperature by detecting the wavelength change.

Strain Monitoring and Installation Adjustment of Satellite–Rocket Connection Device Based on Distributed Optical Fibers

The study on prestressed cable stress based on Brillouin-optictime optic fiber sensor

Monitoring the stress of the post-tensioning cable using fiber optic distributed strain sensor

Strain Transfer Mechanism in Surface-Bonded Distributed Fiber Optic Sensors under Different Strain Fields

Characterizing the strain transfer on the sensing cable-soil interface based on triaxial testing

Spiral Deployment of Optical Fiber Sensors for Distributed Strain Measurement in Seven-Wire Twisted Steel Cables, Post-Tensioned against Precast Concrete Bars

Study of Large Strain OFDR Sensor Based on Inclined Transfer Structure

Structural health monitoring of satellite board based on high-performance fiber optic grating sensor

Performances of Distributed Fiber Optic Strain Sensor with Thin-Walled Ring

Derrick Stress Monitoring System Based On Fiber Bragg Grating Sensor Technology

Strain transfer mechanism in surface-bonded distributed fiber-optic sensors subjected to linear strain gradients: Theoretical modeling and experimental validation

A Novel Method of Embedding Distributed Optical Fiber Sensors for Structural Health Monitoring

Strain Measurement Technology and Precision Calibration Experiment Based on Flexible Sensing Fiber

Study on the Fixation Technique of Optical Fiber Based on BOTDR

Calibration test researches on distributed optical fiber strain sensors

Theoretical and Experimental Analyses on Strain Transferring of Distributed Optical Fiber Sensor

Comparison of DOFS Attachment Methods for Time-Dependent Strain Sensing

EXPERIMENTAL STUDY ON MONITORING OF STRESS FOR PRESTRESSED ANCHORAGE CABLE USING DISTRIBUTED FIBER OPTIC SENSOR

Preliminary Test for 3D Surface Strain Measurement in the Tower and Foundation of Offshore Wind Turbines Using DOFS

Application of Optical Fiber-Based Strain Sensing for the Full-Scale Static and Fatigue Tests of Aircraft Structure

Deformation measurement based on high resolution distributed optical fiber sensing and conjugated beam method