Abstract:Electrically-assisted forming has been proven to be an efficient process in terms of reducing forming flow stress, improving formability and supressing the springback for different hard-to-deform alloys. However, there is a controversial debate about whether the flow stress reduction with the introduction of electric current into a metallic specimen undergoing plastic deformation is attributed to Joule heat, additional athermal effect, namely the electroplasticity, or their combination thereof. There is a lack of thorough understanding of different mechanisms inducing the flow stress reduction and formability improvement, which would hinder the development and application of innovative electrically-assisted forming processes. Most prior works have examined only one or two materials with similar electroplastic behaviours, making it difficult to resolve this debate. In this study, three typical materials with diverse electroplastic behaviours, i.e. copper, SS304 and Ti6Al5V, were investigated and compared via electrically-assisted tensile tests and thermally-assisted tensile tests. The flow stress of the copper specimens in the electrically-assisted tensile test was lower than that in the thermally-assisted tensile test, which verifies the existence of electroplasticity. However, the flow stresses of the SS304 specimens in the electrically-assisted tensile test and thermally-assisted tensile test were similar at the same temperature, indicating that the athermal effect on the flow stress is not evident. For the Ti6Al4V specimens, the athermal stress reduction was not significant at lower current densities. However, the electrically-assisted and thermally-assisted tensile tests results began to differ when the current density exceeded 37.6 A/mm2. According to the further discussion on the microstructure evolution of different materials, the introduced current improves the dislocation motions and recovery and consequently reduces the flow stress in simple face-centered cubic structure materials such as copper. However, these effects can be suppressed by stronger effects such as the solution hardening in stainless steels. The current also affects the phase transition, which in turn influences the hardening behaviours of Ti6Al4V. By clarifying the cause of conflicting electroplastic effects, a uniform analytical method calculating the short- and long-range stresses that considers the correlation of electrical and thermal effects on dislocation motion, solution hardening and phase transformation was developed for electrically-assisted forming processes. The model was also experimentally verified.

Establishment of the Constitutive Equations of TC4 Titanium Alloy for Electroplasticity

Dynamic recrystallization of Ti-6Al-4V titanium alloy based on cellular automata

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

Electroplasticity in electrically-assisted forming: Process phenomena, performances and modelling

Hot Deformation and Constitutive Modeling of TC21 Titanium Alloy

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Effect of Angle between Pulse Current and Load Direction on Flow Stress of Ti-6Al-4V Alloy under Uniaxial Tension

Deformation Behavior and Constitutive Model for Isothermal Compression of TC4 Alloy

Research on Johnson–Cook Constitutive Model of γ-TiAl Alloy with Improved Parameters

Parametric Analysis and Improvement of the Johnson-Cook Model for a TC4 Titanium Alloy

Study on the Constitutive Modeling of (2.5 vol%TiB + 2.5 vol%TiC)/TC4 Composites under Hot Compression Conditions

Processing map of titanium alloy TC4 and its application for plate rolling analyses

Investigation of hot deformation behavior and microstructure evolution of TC18 alloy and establishment of constitutive equation under friction-temperature correction

Defect reconfiguration in a Ti–Al alloy via electroplasticity

Phenomenological Constitutive Model and Physical Constitutive Model of Hot Deformed Dual-Phase Ti-5Al-4Sn-2Zr-5Mo Alloy

Constitutive Model and Cutting Simulation of Titanium Alloy Ti6Al4V after Heat Treatment

Electrical-thermal-mechanical coupled modeling and simulation on deformation behaviors of Ti6554 alloy in electrically-assisted micro-tension

Predicting The Tensile Behavior Of Ti-6.6al-3.3mo-1.8zr-0.29si Alloy Via The Temperature-Dependent Crystal Plasticity Method

Hot deformation behavior and microstructure evolution of TC11 dual-phase titanium alloy

Dynamic Mechanical Properties and Modified Material Constitutive Model for Hot Forged Ti2AlNb over Wide Ranges of Temperature and Strain Rate

Influence of silicide and texture on the room temperature deformation size effect of Ti65 alloy sheets/foils and its constitutive model modification