Abstract:Enhancing inlet gas temperature in aero/gas turbines to reduce their carbon-footprint, has led to a strive for better performing inlet cooling mechanism of the turbine blades. The internal cooling of the blades is made by ceramic cores in their casting process, but conventional ceramic molding has long reached its maximum possible geometrical complexity, hence shedding light on 3D printing of these cores. The objective of this study is to develop low-viscous, fully stabilized, commercially viable ink for vat-photopolymerization of silica-based ceramics. This paper investigates the best dispersion type and amount for different formulated monomer mixtures, and explains the best correlation between viscosity, solid loading, binders, dispersants, peeling forces and mechanical properties, and offers an optimized mixture to avoid the common ceramic printing issue, namely crack propagation of cores during sintering. Among five dispersant agents, the SOL20, SOL24 and FA4611 exhibited better performance than other dispersion agents, and the optimum concentration level for each binder and dispersant agent was ensured through sedimentation test. Their dispersion capability and long-term stability were further investigated to designate the best dispersion agent for each binder system. Further verification was made by sedimentation study of the samples at 40 °C for 40 days and reducing the superficial area of the used powder mixture. According to the result of the rheology analysis, the best dispersions were achieved using SOL20 for the loaded binder mixtures of M1 and M4, SOL24 for M3and FA4611 for M2. The instability of M1 and M2 with their respective dispersant agent was coordinated through the thixotropic agent of TX/2, and complete stabilization and near-Newtonian behavior were achieved. However, the research showed that the addition of TX/2 to fully stabilized M4 and M2 suspensions negatively impacts the mixtures' rheological behavior from near-Newtonian to shear-thickening. In the final stage of this study, peeling forces, sintering and three-point bending tests were conducted to determine the final formulated suspension to print ceramic core components. M4 and SOL20 combination was selected for SiO 2 -ZrSiO 4 loading and dispersing, respectively. The impact of solid loading between the range of 58 and 65 vol.% on the rheological behavior of the final suspension and the mechanical properties of sintered bodies were investigated to assign an optimum solid rate. The adequate strength on sintered and degree of viscosity for ceramic vat-polymerization processing was achieved at 58 vol.%. Lastly, a validation study is conducted by printing a complex ceramic core model by a commercial LCD hobby printer. This validation shows the significance of this study to scale up the manufacturing of complex-shaped ceramic cores and to revolutionize the sector, by printing inexpensive and readily available irregular-shaped (non-atomized) ceramic powder, using the most cost-effective LCD printers (non-specialized expensive ceramic printers).

Vat photopolymerization based Photoinhibition aided Ceramic additive manufacturing (PinCAM)

Vat Photopolymerization of Ceramic Parts: Effects of Carbon Fiber Additives on Microstructure and Mechanical Performance

Printing Depth Modeling, Printing Process Quantification and Quick-Decision of Printing Parameters in Micro-Vat Polymerization

How to Improve the Curing Ability during the Vat Photopolymerization 3D Printing of Non-Oxide Ceramics: A Review

High-resolution multiceramic additive manufacturing based on digital light processing

Research progress of the defects and innovations of ceramic vat photopolymerization

Enhancing 3D printed ceramic components: The function of dispersants, adhesion promoters, and surface-active agents in Photopolymerization-based additive manufacturing

Research progress on crack formation mechanism and inhibition strategy for ceramic additive manufacturing

Vat photopolymerization 3D printing of ceramics: Effects of fine powder

Binder stabilization and rheology optimization for vat-photopolymerization 3D printing of silica-based ceramic mixtures

In-situ Interferometric Curing Monitoring for Digital Light Processing based Vat Photopolymerization Additive Manufacturing

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

Photopolymerization-based additive manufacturing of ceramics: A systematic review

Fabrication of ceramics using photosensitive slurries: A comparison between UV-casting replication and vat photopolymerization 3D printing

Novel camphene/photopolymer solution as pore-forming agent for photocuring-assisted additive manufacturing of porous ceramics

Forming ability and quality of fine ceramic structure fabricated by vat photopolymerization

Influence of dispersant concentration toward enhancing printing precision and surface quality of vat photopolymerization 3D printed ceramics

On enhancing the manufacturability and conversion of additively manufactured polymer-derived ceramics

Slurry-based photoinitiator jetting process for ceramic additive manufacturing

A review of defects in vat photopolymerization additive-manufactured ceramics: Characterization, control, and challenges

Continuous fibre reinforced Vat photopolymerisation (CONFIB-VAT)