Abstract:Background context: Facet joints have been discussed as influential factors in the development of lumbar degeneration, which includes disc herniation and degenerative lumbar spondylolisthesis. Facet orientation (FO) and facet tropism (FT) are two important structural parameters of the lumbar facet joints. Many previous studies have focused on single parameter analysis of the lumbar spine. Owing to the correlation between independent variables, single-factor analysis cannot reflect the interaction between variables; however, there has been no corresponding biomechanical method developed to address this problem. Purpose: To investigate the complex biomechanical influences on the lumbar spine when vertebral FO and FT are varied using finite element analysis (FEA) and contour maps visualization, and analyze the biomechanical role of facet joint structural parameters in the process of lumbar degenerative diseases. Study design: A biomechanical modelling, analysis, and verification study was performed. Methods: A three-dimensional non-linear FEA model of 3 denucleated intervertebral discs (L2-3, L3-4, L4-5) with adjacent vertebral bodies (L2-L5) was created. Previously performed in vitro experiments provided experimental data for the range of motion in each load direction that was used for calibration. For 12 lumbar models, different facet joint angles relative to the sagittal plane at both L3-4 facet joints were simulated for 35°≤FO≤50° and 0°≤FT≤15°. By modifying different values of FO and FT, FEA simulation of different lumbar spine models was performed. Contour maps were used to visualize the FO- and FT-relevant data. Results: Under flexion, extension, and torsion moments, facet joint contact force and intradiscal stress increased with increasing FT. In the condition where FT remained 0° and increasing FO values, facet joint contact force and intradiscal stress remained low with no apparent increasing or decreasing trend when the model was under flexion, extension, and torsion moments. In the condition where FO and the FT values were varied at the same time, the highest force and stress regions in the contour maps were observed when all three types of moments were applied. Stress distributions of the L3-4 disc with different FT and FO values showed disc stress increased significantly with increases of FT and was concentrated on the ipsilateral region of the facet joint with the more sagittal orientation. Conclusions: The combination of FO and FT has an important impact on the corresponding disc and facet joints, but FT played a more significant role. Moreover, disc stress was concentrated on the ipsilateral region of facet joint with greater sagittal orientation when FT existed. FT with high sagittal orientation may increase risk of recurrent LDH due to increase ipsilateral disc pressure. Clinical significance: These biomechanical findings may help clinicians to understand the prognosis of some lumbar degenerative conditions.

Combined effect of artificial cervical disc replacement and facet tropism on the index-level facet joints: a finite element study

A comparative study of the effect of facet tropism on the index-level kinematics and biomechanics after artificial cervical disc replacement (ACDR) with Prestige LP, Prodisc-C vivo, and Mobi-C: a finite element study

Contribution of Sagittal Orientation of Facet Joints and Disc Degeneration to Degenerative Spondylolisthesis in Lumbar Spine: A Finite Element Research

Finite element analysis into the effect of discectomy on lumbar biomechanical characteristics

Influence of the Morphology of Lumbar Motion Segment on Isthmic Stress and Facet Contact Force: A Finite Element Analysisangzh

Topping-off surgery vs posterior lumbar interbody fusion for degenerative lumbar disease: a finite element analysis

Effect of Facet Tropism on Postoperative Cervical Range of Motion after Single-Level Cervical Disc Arthroplasty.

Effects of cervical total disc replacement versus anterior cervical discectomy and fusion on biomechanics of the segments adjacent to the operation level

Mechanical influence of facet tropism in patients with chronic discogenic pain disorder

Segment selection for fusion and artificial disc replacement in the hybrid surgical treatment of noncontiguous cervical spondylosis: a finite element analysis

Biomechanics of Artificial Disc Replacements Adjacent to a 2-Level Fusion in 4-Level Hybrid Constructs: an in Vitro Investigation

The biomechanical influence of facet joint parameters on corresponding segment in the lumbar spine: a new visualization method

Finite element model predicts the biomechanical performance of cervical disc replacement and fusion hybrid surgery with various geometry of ball-and-socket artificial disc

Biomechanical Evaluation of Intervertebral Fusion Process After Anterior Cervical Discectomy and Fusion: A Finite Element Study

In vitro study on biomechanical comparison between cervical arthroplasty and fusion

Biomechanical Effect of C 5 /C 6 Intervertebral Reconstructive Height on Adjacent Segments in Anterior Cervical Discectomy and Fusion - A Finite Element Analysis

Biomechanics of Hybrid Anterior Cervical Fusion and Artificial Disc Replacement in 3-Level Constructs: an in Vitro Investigation.

External and internal responses of cervical disc arthroplasty and anterior cervical discectomy and fusion: A finite element modeling study

Influence of the deviated center of rotation on facet joint degeneration after cervical disc replacement – an in vivo study with a minimum of 10-year follow-up

An Eight‐Year Follow‐Up Study on the Treatment of Single‐Level Cervical Spondylosis Through Intervertebral Disc Replacement and Anterior Cervical Decompression and Fusion

Artificial Cervical Disc Replacement in Cervical Spondylosis