Abstract:The central diaphragm is often used to reduce the span to maintain the stability and safety of structure in the construction of large-span loess tunnel due to the structure complexities. In this paper, relying on the field monitoring and measurement for Wangcun tunnel in Huangling-Yan’an expressway expansion project, the crown settlement and horizontal convergence of primary support steel rib and central diaphragm steel rib during the construction are analyzed by the upper bench CD method. According to the internal force transfer, deformation coordination, and arch foot displacement between the two structures, the support system is regarded as the arch-beam fixed structure with three times of statically indeterminate and movable abutment under the loads, and the mechanical calculation model of sidewall steel rib and the central diaphragm structure bearing loads and deformation together is established. Finally, through the mechanical model mentioned above, the deformation characteristics of central diaphragm structure and the horizontal convergence in the upper bench of tunnel are calculated and analyzed. The research shows the following: (1) the accumulated settlement of sidewall steel rib in Part I is greater than that of the sidewall steel rib in Part II, and the accumulated settlement of each part at the support structure during the tunnel excavation is less than the reserved deformation of 150 mm specified in the tunnel excavation; (2) the settlement located at the waist and maximum excavation line position of central diaphragm is mainly affected by the excavation of Parts I and II in upper bench; (3) during the whole excavation process, the excavation of Part I and Part II has the greatest influence on the convergence at arch waist and the maximum excavation line position in Part I, and the convergence at the above two positions all experienced four stages of “convergence-expansion-convergence-gradual stability”; and (4) the errors between the horizontal convergence and the deformation of central diaphragm obtained by the mechanical model and the field monitoring data are between 12.7% and 27.5%. The calculated results are in good agreement with the actual situation. The research can provide a theoretical basis for the study of deformation and mechanical properties for support structure in the construction of large-span loess tunnel by the upper bench CD method.

Study on the bending resistance performance of lightweight prefabricated frame tunnel components

Theoretical Analysis of Longitudinal Vertical Displacement of Subway Tunnels Caused by the Construction of Steel Casings for Bridge Piles

Research on Longitudinal Structural Rigidity Properties of Shield Tunnel

Experiments and Numerical Simulation of the Reinforcement Effect of Channel-Steel-reinforced Shield Tunnel Segments under Unloading Conditions

Full-scale Experimental and Structural Characterization Study of Shield Tunnel Reinforcement under Ground Stacking Loads

Full-Scale Experimental Study on the Effect of Ground Surcharge on the Stress and Deformation of Shield Tunnels

Study of Deformation Behaviors and Mechanical Properties of Central Diaphragm in a Large-Span Loess Tunnel by the Upper Bench CD Method

Prefabricated Urban Underground Utility Tunnels: A Case Study on Mechanical Behaviour with Strain Monitoring and Numerical Simulation

Characterizing the bending behavior of underground utility tunnel roofs in a fabricated composite shell system

A study on bearing characteristic and failure mechanism of thin-walled structure of a prefabricated subway station

Connection of the prefabricated updeck of road tunnels by a short lap-spliced joint using ultra-high-performance fiber-reinforced concrete

Design and application of a prefabricated structure for large-span arch open-cut highway tunnels

Numerical simulation and simplified analytical model for the longitudinal joint bending stiffness of a tunnel considering axial force

Study on the mechanical properties of prefabricated assembled cover arch reinforcements in tunnels

The application of steel-concrete-steel composite structures in immersed tunnels

Nonlinear static behavior analysis of single/double-layer frame tunnels with mortise and tenon joint

A New Design Method of Shield Tunnel Based on the Concept of Minimum Bending Moment

The mechanical deformation characteristics of the internal structure of large diameter shield tunnel in different construction stages

Joints mechanical characteristics of prefabricated subway station considering bending stiffness difference

Seismic Performance of Joints of Prefabricated Corrugated Steel Utility Tunnels Part(I)–Experimental Analysis

Research on mechanical behaviour of tapered concrete-filled double skin steel tubular members with large hollow ratio subjected to bending