Abstract:The fundamental aspects of site preference of alloying elements on sublattice of the strengthen γ′ phase with L12 structure have not been well understood, which hinders the optimized design of advanced Ni-based high-temperature alloys. In this contribution, the temperature- and composition-dependent site occupying preferences of the binary, ternary, and quaternary of Ni3Al-based γ′ phase alloyed with Mi where Mi represents the additional transitional metals Co, Cr, Cu, Fe, Mn, Mo, Re, Ta, Ti, V, or W atoms (arranged in alphabetical order) chosen frequently, were studied using a two-sublattice thermodynamic model (Ni, Al, Mi)1a(Ni, Al, Mi)3c. The site occupying fractions (SOFs) were calculated based on a thermodynamic database established in this work, where the thermodynamic data of the end-members involved were obtained using first-principles calculations and phonon spectrum calculations. The calculated SOFs results show that there is an obvious site preference for stoichiometry binary Ni3Al, and its site configuration changes from (Al)1a(Ni)3c at room temperature to (Al0.9984Ni0.0015)1a (Al0Ni0.9994)3c at 1273 K. For the γ′ phase with the composition 78Ni-26Al-4Mi (atom ratio and xNi/xAl = 3:1), Mo atoms always preferred to occupy the 1a sublattice (Al site), Co, Mn, and Ti atoms always prefer the 3c sublattice (Ni site) in the whole temperature range, while the site preference of Cr, Cu, Fe, Re, Ta, V, or W atom is affected by temperature. For example, when the heat treatment temperature is lower than 700 K, Cr, Cu, Fe, Ta, V, and W atoms occupy the 1a and 3c sublattice randomly, and Re atoms prefer to 3c sublattice, while when the heat treatment temperature is higher than 1273 K, Cr, Cu, and W atoms prefer 3c sublattice, Fe and Ta atoms prefer to 1a sublattice, while all Re atoms occupy the 3c sublattice exclusively, and all V atoms occupy the 1a sublattice exclusively, respectively. Likewise, the site preference of the quaternary system with selective compositions 78Ni-26Al-2 M1-2 M2 was also predicted. Based on calculated SOFs results, the mechanical and thermodynamic properties were studied at the ground state. It has been revealed that Cr, Re, and V doping can improve the microhardness of Ni3Al alloys; in particular, the effect of Cr is extraordinary; and all elements, except Mn, Mo, and Ti, would enhance the bulk modulus of Ni3Al-based γ′ phase, in which Mn have the greatest influence on reducing the bulk and shear modulus, respectively. Furthermore, all the B/G ratios of the computed Ni3Al-based γ′ phase are >1.75, showing inherent ductility. Only Cr doping significantly enhances the Debye temperature of the Ni3Al-based γ′ phase.

Compressive behavior and elastic properties of Ni-based γ/γ’ ternary model superalloys: First-principles calculations and rule of mixtures predications

Effect of Alloying Elements on Lattice Misfit and Elasticities of Ni-based Single Crystal Superalloys by First-Principle Calculations

Density functional theory study of the thermodynamic and elastic properties of Ni-based superalloys

Transition Metal Solutes in Ni-based Ternary Model Superalloys: Partitioning and Effects on Elastic Properties from First-Principles Calculations

Transition-metal Alloying of Γ′−ni3al : Effects on the Ideal Uniaxial Compressive Strength from First-Principles Calculations

The Effects of Combining Alloying Elements on the Elastic Properties of Γ -Ni in Ni-based Superalloy: High-throughput First-Principles Calculations

Alloying-element Dependence of Structural, Elastic and Electronic Properties of Nickel-Based Superalloys: Influence of Γ’ Volume Fraction

First-Principles Calculations for the Elastic Properties of Ni-Base Model Superalloys: Ni/Ni3al Multilayers

Dependence of Mechanical Properties on the Site Occupancy of Ternary Alloying Elements in Γ'-Ni3al: Ab Initio Description for Shear and Tensile Deformation

Transition-metal-element Dependence of Ideal Shear Strength and Elastic Behaviors of Γ′-Ni3al: Ab Initio Study to Guide Rational Alloy Design

Influence of Alloying Elements on the Elastic Properties of Ternary and Quaternary Nickel-Base Superalloys

Composition Effect on Elastic Properties of Model NiCo-based Superalloys

First-Principles Calculations of Elastic and Thermodynamic Properties for Multi-component Co-based Superalloys

Assessing Elastic Property and Solid-Solution Strengthening of Binary Ni–Co, Ni–Cr, and Ternary Ni–Co–Cr Alloys from First-Principles Theory

Influence of Alloying Elements Upon the Theoretical Tensile Strength of Ni-based Model Superalloy: Γ-Ni/γ′-ni3al Multilayer

Theoretical Calculations of the Ideal Strength of Ni, NiAl and Ni3Al in Tension and Shear

Correlation of the properties of quasi-ternary Ni-based superalloys computed from DFT to elemental properties enabling predictions on the behavior of metallic alloying elements

Elastic behavior of binary and ternary refractory multi-principal-element alloys

The site preference and doping effect on mechanical properties of Ni3Al-based γ′ phase in superalloys by combing first-principles calculations and thermodynamic model

Site preference and effect on shear deformation of co-alloying elements addition to γ′-Ni3Al phase in Ni-based single crystal superalloys

Effect of substituting Mo for W on γ/γ′ partitioning behaviors of alloying elements in heat-treated second generation Ni based single crystal superalloys: An atom probe tomography study