Abstract:The generation of both spatters and pores during the laser powder bed fusion (LPBF) process has a substantial detrimental effect on mechanical properties. Consequently, eliminating pores is an urgent problem to ensure the quality and yield of fabricated parts. The aim of this study is to evaluate the effect of the critical variables such as laser power (W), linear energy density (J/mm) and volumetric energy density (J/mm3) on pore characteristics (diameters and numbers), microstructure and mechanical properties. In addition, this study first demonstrates that the spatter is hypothesized to be an additional cause of porosity, beyond those traditionally understood to be resulting from process parameters or feedstock moisture. In our study, three different types of landed droplets were observed, i.e., hollow droplets, semi-hollow droplets and solid droplets. The hollow and semi-hollow droplets triggered the formation of pores during solidification. The results also revealed that the pores could not be eliminated completely, and the intense spattering resulted in the formation of more pores. Furthermore, the effects of process parameters on pore characteristics and mechanical properties are complex, and it is necessary to consider the combined effects of laser power, linear energy density and volumetric energy density. For the experiments with constant volumetric energy densities of 111.1 J/cm3, the quantities of pores reduced with a decrease in linear energy density from 0.2 J/mm to 0.15 J/mm, and the ultimate tensile strength increased to 475.18 MPa. When the linear energy density decreased to 0.12 J/mm, the tensile strength decreased to 422.55 MPa. As the result of insufficient linear energy density, some large irregular pores (larger than 100 μm) were observed inside the specimen. Besides, for the experiments with constant linear and volumetric energy densities of 0.2 J/mm and 111.1 J/cm3, the number of pores decreased while the ultimate tensile strength increased with laser power and scanning speed increased simultaneously. The highest ultimate tensile strength exceeded 480 MPa when the laser power was greater than 360 W.

Direct observation of pore formation mechanisms during LPBF additive manufacturing process and high energy density laser welding

In-Situ Characterization of Pore Formation Dynamics in Pulsed Wave Laser Powder Bed Fusion

Dynamics of pore formation during laser powder bed fusion additive manufacturing

Formation mechanisms of lack of fusion and keyhole-induced pore defects in laser powder bed fusion process: A numerical study

Understanding keyhole induced-porosities in laser powder bed fusion of aluminum and elimination strategy

Pore defects in Laser Powder Bed Fusion: Formation mechanism, control method, and perspectives

Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter and denudation zones

Quantification of Interdependent Dynamics during Laser Additive Manufacturing Using X‐Ray Imaging Informed Multi‐Physics and Multiphase Simulation

Identifying the keyhole stability and pore formation mechanisms in laser powder bed fusion additive manufacturing

Revealing mechanism of pore defect formation in laser directed energy deposition of aluminum alloy via in-situ synchrotron X-ray imaging

Publisher Correction: Pore Elimination Mechanisms During 3D Printing of Metals

Influence of Laser Post-Processing on Pore Evolution of Ti–6Al–4V Alloy by Laser Powder Bed Fusion

Pore Formation Driven by Particle Impact in Laser Powder-Blown Directed Energy Deposition.

In Situ X-ray Imaging of Pore Formation Mechanisms and Dynamics in Laser Powder-Blown Directed Energy Deposition Additive Manufacturing

Pore Formation and Prevention in Deep Penetration Pulsed Laser Welding

Formation mechanism of pore defects and surface ripples under different process parameters via laser powder bed fusion by numerical simulation and experimental verification

Investigation of Laser-Powder Interaction in Laser Powder Bed Fusion Process in Additive Manufacturing

Keyhole fluctuation and pore formation mechanisms during laser powder bed fusion additive manufacturing

Investigation of Pore Reduction in Hybrid Joints of Conventionally and Additively Manufactured AlSi10Mg Using Electron Beam Welding

Numerical studies of melt pool and gas bubble dynamics in laser powder bed fusion process

Laser powder bed fusion of AlSi10Mg: Influence of energy intensities on spatter and porosity evolution, microstructure and mechanical properties