Kai Guo,Jianxu Jiang,Deqiang Zhang,Linyuan Meng,Yiran Zhang,Xiantao Fan,Hongsheng Zhang
Abstract:The reciprocating plate column is a kind of column with the plates driven by a geared motor, and it has advantages in regard to efficiency compared to traditional columns in the extraction process, however, it comes with an increase in energy consumption. A new type of reciprocating plate column driven by electro-permanent magnet technology (EPM) is proposed in this paper to obtain a better performance with lower energy consumption. The feasibility and performance of the proposed column is studied by numerical simulation and experiments with a kerosene–water system. The electro-permanent magnet chuck could provide a maximum amplitude of 12 mm in this study. Kerosene was used as the dispersed phase, and deionized water was used as the continuous phase, in a laboratory-scale 35 mm diameter reciprocating plate column driven by EPM. Hydrodynamic performance experiments were carried out with different flowrates of both phases and reciprocating frequencies. The experimental results show that the electro-permanent magnet chuck, which serves as the driving device of the reciprocating plate column, plays the role of adding energy and increasing the droplet breakage. In addition, the energy consumption of the reciprocating plate column with traditional geared motor and electro-permanent magnet chuck is calculated respectively. Compared with the traditional geared motor, the energy saving of the electro-permanent magnet chuck is as high as 98.55%.
What problem does this paper attempt to address?
### Problems the Paper Aims to Solve
The paper aims to address the issue of high energy consumption in traditional reciprocating plate columns during the extraction process. Although traditional reciprocating plate columns are more efficient than conventional extraction equipment, their operation requires additional energy input, leading to high energy consumption. Therefore, the paper proposes a new type of reciprocating plate column driven by Electromagnetic Permanent Magnet (EPM) technology to achieve higher efficiency and lower energy consumption.
### Specific Research Content
1. **Background Introduction**:
- Solvent extraction is a chemical separation technology widely used in fields such as pharmaceuticals, petrochemicals, and hydrometallurgy.
- Traditional extraction equipment includes mixing tanks, spray towers, packed towers, and sieve plate towers, but these devices have limited mass transfer efficiency and are difficult to improve through external agitation.
- To improve mass transfer efficiency, Van Dijck proposed extraction columns that enhance mass transfer efficiency through pulsating fluids or reciprocating sieve plates. Karr further developed this reciprocating sieve plate column, which increases mass transfer efficiency by periodically moving the sieve plates up and down to break droplets.
2. **Design and Principle of the New Reciprocating Plate Column**:
- This paper proposes a reciprocating plate column driven by Electromagnetic Permanent Magnet (EPM) technology. The EPM chuck can provide sufficient suction to move the sieve plates up and down, thereby breaking droplets and improving mass transfer efficiency.
- The working principle of the EPM chuck is to control the magnetization and demagnetization states through electromagnetic pulses, thus achieving the reciprocating motion of the sieve plates. Compared to traditional gear motor drive methods, EPM technology has advantages such as low energy consumption, compact structure, and no heat generation.
3. **Experimental Design and Methods**:
- The experimental setup includes a laboratory-scale reciprocating plate column with a diameter of 35 millimeters, equipped with stainless steel perforated plates and an EPM chuck installed at the top.
- Kerosene was used as the dispersed phase and deionized water as the continuous phase in the experiments. The hydrodynamic performance was studied by adjusting the flow rates of the two phases and the reciprocating frequency.
- The experimental design matrix included 4 different dispersed phase velocities, 4 different continuous phase velocities, and 4 different reciprocating frequencies, resulting in a total of 64 hydrodynamic experiments.
4. **Experimental Results and Analysis**:
- The experimental results showed that the EPM chuck, as the driving device for the reciprocating plate column, effectively increased droplet breakage and improved mass transfer efficiency.
- Compared to traditional gear motor drives, the energy consumption of the EPM chuck was reduced by up to 98.55%.
- By analyzing the Sauter mean droplet diameter and dispersed phase holdup under different conditions, the superiority of the new reciprocating plate column in hydrodynamic performance was verified.
### Conclusion
The paper successfully proposes and validates a new type of reciprocating plate column driven by Electromagnetic Permanent Magnet (EPM) technology, which not only improves mass transfer efficiency but also significantly reduces energy consumption. This research provides a new solution for high-efficiency and energy-saving in the solvent extraction process.