Abstract:To determine the impact of selected conditions of abrasive treatment on the value and distribution of microhardness and residual stresses in layers carburised by a continuous single-piece flow method. Reference pieces were low pressure carburised at 920°C and then heat-treated in a 4D Quench heat treatment chamber at a pressure of 7 bar and tempered at 190oC for 3 hours. In the next stage, samples were ground at various vw piece speeds, introducing grinding fluid into the cutting zone using the WET spraying method or using the MQL method at a minimum flow rate. The distribution of microhardness and residual stresses generated in the technological outer layer of the pieces following heat and chemical treatment and the grinding process was measured. Results of the tests indicated that the vw piece speed and method used to supply cooling and lubricating fluid to the grinding zone had an impact on selected parameters of the technological outer layer of flat samples made of 20MnCr5 steel. The process of grinding using an electrocorundum grinding wheel results in a deterioration of residual stresses in the material. For each of the three analysed vw piece speeds, reduced changes in material microhardness prior to cutting occur in the outer layer of samples ground using GF supplied at a minimum flow rate using the MQL method. Environmental considerations and having to conform to increasingly stringent regulations related to environmental protection and employee safety motivate researchers and businesses to entirely eliminate or reduce the use of grinding fluids in the grinding process and, therefore, to optimise grinding technology. Modern manufacturing industry requires the grinding process, which follows heat and chemical treatment, to be performed with the highest possible efficiency. However, retaining high parameters of the technological outer layer in comparison to the sample material following vacuum carburisation (before grinding) is extremely difficult. An optimised configuration of parameters of the grinding process and method of supplying grinding fluids enables meeting the current and future high expectations of the industry in this regard. The tests have enabled us to determine the impact of the applied vw workpiece speed and method of supplying grinding fluid on microhardness and residual stresses. Generally speaking, grinding with an electrocorundum grinding wheel results in a deterioration of residual stresses. For both methods of supplying GF (WET and MQL), the distribution of microhardness in the material of the samples ground with the highest workpiece speed (18.0 m/min) indicated no significant differences with regard to the distribution of microhardness in the material of the samples following heat and chemical treatment.

Influence of High‐Pressure Grinding Parameters on Surface Topography and Microstructure

Numerical Investigation of the Evolution of Grit Fracture and Its Impact on Cutting Performance in Single Grit Grinding

The influence of grinding wheel type on microhardness and residual stresses in vacuum-carburised 20MnCr5 steel using the single-piece flow method

Effects of a New Type of Grinding Wheel with Multi-Granular Abrasive Grains on Surface Topography Properties after Grinding of Inconel 625

Analysis of Grindability and Surface Integrity in Creep−Feed Grinding of High−Strength Steels

Surface modification of ultrahigh strength 300M steel under supercritical carbon dioxide (scCO2)-assisted grinding process

The influence of workpiece speed on microhardness and residual stresses in vacuum-carburised 20MnCr5 steel using the single-piece flow method

Influence of Grinding Pressure on Removal Behaviours of Rail Material

Adapting the Surface Integrity of High-Speed Steel Tools for Sheet-Bulk Metal Forming

Effect of process parameters on hardness and microstructure of 18CrNiMo7-6 carburized steel in high-speed cylindrical grinding

Process parameter optimization and surface integrity evolution in the high-speed grinding of TiAl intermetallics based on grey relational analysis method

Study on the effect of the strengthen grinding process surface coverage on the micro-morphology, micro-hardness, roughness, and residue stress of GCr15 bearing steels

Study on grinding performance during ultrasonic vibration-assisted grinding ultra-high strength steels

An experimental and theoretical analysis of surface generation in the ultra-precision grinding of hard and brittle materials

Study of 40Cr surface modification grinding force and temperature based on microstructure evolution mechanism

The influence of grinding conditions on surface roughness parameters of 20MnCr5 steel vacuum-carburised by single-piece flow method

Time Dependent Behavior Analysis of Inconel 718 in High Speed Grinding Process

Distinguishing effect of turning and grinding on the surface integrity and fatigue performance of ultra-high strength steel

Familial Transmission of Eating Behaviors in Preschool‐aged Children

New layering strategy and the gradient microstructure distribution of surface metamorphic layer for 8Cr4Mo4V steel by grinding

Grindability studies of thermomechanically processed advanced high strength steel using sol-gel and fused alumina grain-based grinding wheels