Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

An illustrative understanding on strengthening in stability and efficiency of perovskite solar cells: Utilization of the perovskite-constructed polymer hybrid system of PHQACl-CN inclusion

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Reconstructing Subsurface Lattice for Stable Perovskite Photovoltaics

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Multifunctional Enhancement for Highly Stable and Efficient Perovskite Solar Cells

Stable and efficient perovskite solar cells via hydrogen bonding and coordination

Improving Efficiency and Stability of Perovskite Solar Cells Enabled by A Near-Infrared-Absorbing Moisture Barrier

Realizing Stable Perovskite Solar Cells with Efficiency Exceeding 25.6% Through Crystallization Kinetics and Spatial Orientation Regulation

Establishing Multifunctional Interface Layer of Perovskite Ligand Modified Lead Sulfide Quantum Dots for Improving the Performance and Stability of Perovskite Solar Cells

Porphyrinic Metal–Organic Framework Quantum Dots for Stable n–i–p Perovskite Solar Cells

Metastable interphase induced pre-strain compensation enables efficient and stable perovskite solar cells

Deactivating grain boundary defect by bifunctional polymer additive for humid air-synthesized stable halide perovskite solar cells

Efficient and Stable Perovskite Solar Cells by B-Site Compositional Engineered All-Inorganic Perovskites and Interface Passivation

Enhancing Intrinsic Stability of Hybrid Perovskite Solar Cell by Strong, yet Balanced, Electronic Coupling

Stabilization of highly efficient perovskite solar cells with a tailored supramolecular interface

Multifunctional Cross‐Linked Polyurethane Polymer as Interface Layer for Efficient and Stable Perovskite Solar Cells

High‐Efficiency and Stable Perovskite Solar Cells via Buried Interface Modification with Multi‐Functional Phosphorylcholine Chloride

Stabilization of 3D/2D perovskite heterostructures via inhibition of ion diffusion by cross-linked polymers for solar cells with improved performance

Local nearly non-strained perovskite lattice approaching a broad environmental stability window of efficient solar cells

Intermediate Phase Modification Enables High‐Performance Iodine‐Rich Inorganic Perovskite Solar Cells with 3000‐Hour Stability