Abstract:Compressive testing of specimens taken from relatively thin composite plates is difficult, especially due to the occurrence of buckling. To prevent buckling, the central portion of the specimens used for the compression test has smaller dimensions, and the specimens can be guided along their entire length. For these reasons, optical methods, such as digital image correlation (DIC), cannot be used for the compression test and strain rosettes cannot be glued onto the samples to determine Poisson's ratio. In this study, compression tests of a glass fiber-reinforced polymer (GFRP) were conducted using both the ASTM D695 (Boeing version) and a newly proposed method. The new method involves using special specimens that allow T-type rosettes to be bonded to determine Poisson's ratio, whose value of 0.14 was thus determined. SEM images of the failure surfaces were presented and interpreted. A finite element analysis (FEA) of the specimens tested in compression is also presented. The first analyzed case considers the homogeneous and orthotropic composite, loaded with a uniformly distributed force. The normal stress in the central section of the specimen, determined with FEA, has an error of 6.52% compared to that determined experimentally. Additionally, the strain in the center of the strain gauge, determined with FEA, has an error of 4.76% compared to the measured one. In the second case studied with FEA, the sample is loaded with a quasi-concentrated force, which can move in the direction of the symmetry axes of the cross-section, to study the effect of the eccentricity of the compression force on the state of stress. It was shown that the eccentricity of the force has a great influence: the stress distribution in the section of the specimen becomes strongly non-uniform. For a force eccentricity of 0.4 mm in the direction of the OX axis, the minimum stress decreases by 53.7%, and the maximum stress increases by 55.4%. In order to analyze the influence of some manufacturing defects, two other cases were analyzed by FEA, in which it was assumed that the thicknesses of the outer resin layers were modified, making them asymmetrical. For this final FEA, the specimen was considered to be composed of laminates. These results demonstrate the special attention that must be paid to the centric application of force in compression testing.

Tensile Strength Analysis of Polymer Composite Materials Fiber Reinforced in The Fiber boat Application

Biocomposite Innovation: Assessing Tensile and Flexural Performance with Maleated Natural Rubber Additives

Physical analysis and statistical investigation of tensile and fatigue behaviors of glass fiber-reinforced polyester via novel fibers arrangement

Numerical Analysis of Unidirectional GFRP Composite Mechanical Response Subjected to Tension Load using Finite Element Method

Analysis of the Tensile Behavior of FRP Textile for Multi-Scale Fiber Reinforced Cementitious Composite

Experimental investigation on mechanical property analysis of long and short fiber glass

The Effect of Fiber Position and Polymerization Condition on the Flexural Properties of Fiber-Reinforced Composite

Evaluation of tensile properties of fiber metal laminates under different strain rates

Tensile and flexural properties of natural fiber reinforced polymer composites: A review

Investigation of Tensile Behavior of Carbon Nanotube/Coir Fiber/Fly Ash Reinforced Epoxy Polymer Matrix Composite

Effect of glass, carbon, and kevlar fibers on mechanical properties for polymeric composite tubes produced by a unidirectional winding method

Experimental investigation of mechanical properties of jute/hemp fibers reinforced hybrid polyester composites

A New Method for Compression Testing of Reinforced Polymers

Optimization of Tensile Strength and Young's Modulus of CNT-CF/Epoxy Composites Using Response Surface Methodology (RSM)

Influences of nano-SiO2 on the tensile, flexural, and compressive characteristics of the open-hole carbon fiber-reinforced polymer laminated composites: Experimental study

Investigation on the tensile and flexural behavior of coconut inflorescence fiber reinforced unsaturated polyester resin composites

Experimental Determination of Fracture Toughness of Woven/Chopped Glass Fiber Hybrid Reinforced Thermoplastic Composite Laminates

Mechanical, morphological and wear resistance of natural fiber / glass fiber-based polymer composites

Compressive Strength Determined for Ultrahigh Modulus Fiber Reinforced Composites by [90/0]ns Laminates

Investigation of low‐velocity impact behaviors of polymer composites reinforced with different natural fiber fabrics

Effects of fiber type, content, orientation, and surface treatments on the mechanical properties of PAFRP composite