Abstract:Biodegradable plastics in single-use products have increased in popularity as a way to reduce the negative environmental impact of conventional plastics and meet the tightening law regulations. However, their recyclability needs to be assessed, as the environmental behavior of single-use plastics, even if compostable, is not negligible. Polylactide (PLA) is susceptible to thermal, oxidative, hydrolytic, and mechanical degradation during reprocessing, so the conditions of such cycles must be accurately controlled. The necessity of using additives to reduce such degradations during rotational molding, a process with long cycle times and oxidizing atmosphere, has been demonstrated. Chain extenders based on a carbodiimide (Bioadimide® 100 - KI), a methylene diphenyl diisocyanate (MDI), and a polystyrene-acrylic copolymer (Joncryl® ADR-4368c - J) have been added to post-consumer PLA wastes. It has been demonstrated that these three chain extenders enabled obtaining a higher molecular weight of the reprocessed polymer, compared to the ∼50% reduction for the neat PLA. The use of carbodiimide yielded the most similar performance to that of unprocessed raw material. All samples provided adequate thermal stability and processing parameters for the rotational molding. Carbodiimide is considered the most efficient additive, as it increases the molecular mass of the polymer as it remains unchanged after processing. Similarly, KI-modified PLA rheological behavior remains unchanged after processing, which means this compound can reduce thermooxidative and hydrolytic degradation reactions. Thus contributing to the achievement of improved processability and better performance; in particular, impact strength increased from 1.06 ± 0.56 for PLA to 8.12 ± 2.28 kJ/m 2 for KI-modified PLA, and toughness of 5.36 ± 1.61 to 61.49 ± 8.01 J/mm 3 , respectively, leading to rotomolded items without structural defects. On the opposite, the use of Joncryl® and MDI led to structural defects in the rotomolded parts despite a higher molecular weight of the polymer, which resulted in poor mechanical properties, although better than PLA without any additive. All three chain extenders resulted in an amorphous PLA structure with increased glass transition temperature and improved thermal stability, which correlated with the reduced emissions of volatile compounds compared to neat recycled PLA. The presented findings significantly contribute to a better understanding of PLA and its modifications at a molecular scale required for its efficient and possibly environmentally burden-free reprocessing. Gathered knowledge will be crucial for optimizing its environmental performance and widening its applications, particularly in a process with long cycle times and oxidative character, such as rotational molding.

Effect of the Addition of PLA on the Thermal and Mechanical Properties of Reprocessed HDPE

Influence of the Aliphatic Chain Length on the Crosslinking Properties of Aldehydes on Sustainable Bioplastics Obtained from Pea Protein

Rheological and mechanical properties of recycled polyethylene films contaminated by biopolymer

Effect of oligomeric lactic acid plasticizer on the mechanical recycling of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)

Depolymerization and Re/Upcycling of Biodegradable PLA Plastics

Impact of bioplastic contamination on the mechanical recycling of conventional plastics

Study of the Influence of the Reprocessing Cycles on the Final Properties of Polylactide Pieces Obtained by Injection Molding

Hydrothermal Processing of Polylactic Acid: Analysis of Intermediate Products and Toxicity Evaluation of Anaerobically Digestated Residues

Advanced Plastic Waste Recycling—The Effect of Clay on the Morphological and Thermal Behavior of Recycled PET/PLA Sustainable Blends

The use of chain extenders as processing aids in the valorization of single-use polylactide (PLA) products by rotomolding

Upcycling of Poly(Lactic Acid) by Reactive Extrusion with Recycled Polycarbonate: Morphological and Mechanical Properties of Blends

Tuning Biodegradation of Poly (lactic acid) (PLA) at Mild Temperature by Blending with Poly (butylene succinate-co-adipate) (PBSA) or Polycaprolactone (PCL)

Study on Biodegradation Technology for the Structural Change Reaction of Polymer Polylactic Acid

Directed Evolution of Material Binding Peptide for Polylactic Acid-specific Degradation in Mixed Plastic Wastes

The Effect of Mechanical Recycling on the Thermal, Mechanical, and Chemical Properties of Poly (Butylene Adipate-Co-Terephthalate) (PBAT), Poly (Butylene Succinate) (PBS), Poly (Lactic Acid) (PLA), PBAT-PBS Blend and PBAT-TPS Biocomposite

Obtention and characterization of PLA/PHBV thin sheets by solvent casting and extrusion with application in food packaging

Mechanical recycling of poly(lactic acid)/agave fiber biocomposites

Influence of Biodegradable Poly(butylene Carbonate) on Plasticized Polylactide Blown Films

Polylactic acid (PLA): Improve it, use it, and dump it faster

Impact of the thermo-alkaline pretreatment on the anaerobic digestion of poly(butylene adipate-co-terephthalate) (PBAT) and poly(lactic acid) (PLA) blended plastics

Mechanical recycling of biobased polyethylene-agave fiber composites