Evaluation of the Effectiveness of Geogrids Manufactured from Recycled Plastics for Slope Stabilization—A Case Study

Lenin Vicuña,Ximena Jaramillo-Fierro,Paúl Eduardo Cuenca,Brenda Godoy-Paucar,Jorge Daniel Inga-Lafebre,José Luis Chávez,Juan Fernando García,Diana Guaya,Juan Diego Febres

DOI: https://doi.org/10.3390/polym16081151

IF: 5

2024-04-20

Polymers

Abstract:This study aimed to investigate the sustainable use of recycled plastics, specifically polypropylene (PP) and high-density polyethylene (HDPE), in the manufacture of geogrids for geotechnical and civil engineering applications. Plastics were collected from a recycling center, specifically targeting containers used for food, cleaning products, and other domestic packaging items. These plastics were sorted according to the Möbius triangle classification system, with HDPE (#2) and PP (#5) being the primary categories of interest. The research methodologically evaluates the mechanical properties of PP/HDPE (0/100, 25/75, 50/50, 75/25 and 100/0% w/w) composites through tensile and flexural tests, exploring various compositions and configurations of geogrids. The results highlight the superiority of pure recycled HDPE processed into 1.3 mm thick laminated yarns and hot air welded for 20 to 30 s, exhibiting a deformation exceeding 60% in comparison to the PP/HDPE composites. Through SolidWorks® Simulation, it was shown that the adoption of a trigonal geogrid geometry optimizes force distribution and tensile strength, significantly improving slope stabilization efficiency. Based on the results obtained, a laboratory-scale prototype geogrid was developed using an extrusion process. The results underscore the importance of careful composite design and yarn configuration selection to achieve the desired mechanical properties and performance in geogrid applications. It emphasizes the potential of recycled plastics as a viable and environmentally friendly solution for stabilizing slopes, contributing to the reduction in plastic waste and promoting sustainable construction practices.

polymer science

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to evaluate the effectiveness and feasibility of using recycled plastics (especially polypropylene (PP) and high - density polyethylene (HDPE)) to manufacture geogrids in slope stabilization. Specifically, the research aims to:

1. **Material Selection and Treatment**: Through plastic containers (such as food, cleaning products, and other household packaging items) collected from recycling centers, classify, clean, dry, and crush these plastics according to the Möbius triangle classification system (mainly focusing on the HDPE (#2) and PP (#5) categories) to prepare PP/HDPE composites with different proportions (0/100, 25/75, 50/50, 75/25, 100/0% w/w).

2. **Mechanical Property Testing**: Through tensile and bending tests, evaluate the mechanical properties of PP/HDPE composites with different proportions, including elastic modulus, maximum stress, and maximum deformation. The study found that pure recycled HDPE (1.3 - mm - thick laminated yarn, hot - air welded for 20 to 30 seconds) exhibited a deformation capacity of more than 60%, which was superior to PP/HDPE composites.

3. **Geometric Design Optimization**: Using SolidWorks®Simulation software, the effects of different mesh geometries (diamond and triangular) and structural line configurations (woven, filament, and sheet) on force distribution and tensile strength were studied. The results showed that using a triangular mesh geometry could significantly improve force distribution and tensile strength, thereby improving slope - stabilization efficiency.

4. **Prototype Development**: Based on the experimental results, a laboratory - scale geogrid prototype was developed using the extrusion process. The research emphasized the importance of carefully designing composites and selecting appropriate yarn configurations to achieve the required mechanical properties and performance.

5. **Environmental and Economic Impact**: The potential of using recycled plastics to manufacture geogrids in reducing plastic waste and promoting sustainable construction practices was explored, while its cost - effectiveness and environmental impact were also evaluated.

In summary, through systematic experiments and analyses, this paper aims to verify the feasibility and advantages of recycled plastics in geogrid manufacturing, providing an environmentally friendly and effective solution for slope stabilization.