Abstract:As a promising new power source, the proton exchange membrane fuel cell (PEMFC) has attracted extensive attention. The PEMFC engine produces a large amount of waste heat during operation. The excessive temperature will reduce the efficiency and lifespan of PEMFC engine and even cause irreversible damage if not taken away in time. The thermal management system of the PEMFC plays a critical role in efficiency optimization, longevity and operational safety. To solve the problem of high heat production in the operation of the PEMFC, two approaches are proposed to improve the heat dissipation performance of the radiators in thermal management systems. Three kinds of nanofluids with excellent electrical and thermal conductivity–Al2O3, SiO2 and ZnO– are employed as the cooling medium. The radiator parameters are optimized to improve the heat transfer capability. A typical 1D thermal management system and an isotropic 3D porous medium model replacing the wavy fin are constructed to reveal the effects of the nanofluid and the parameters of the radiator performance and the thermal management system. The results show that all three kinds of nanofluids can effectively improve the heat transfer capacity of the coolant, among which the comprehensive performance of the Al2O3 nanofluid is best. When the mass flow rate is 0.04 kg/s and the concentration is 0.5 vol%, the amount of heat transfer of the Al2O3 nanofluid increases by 12.7% when compared with pure water. Under the same conditions, it can reduce the frontal area of the radiator by 12%. For the radiator, appropriate reduction of the fin pitch and wavy length and increase of wave amplitude can effectively improve the spread of heat. The use of fin parameters with higher heat dissipation power results in lower coolant temperatures at the inlet and outlet of the stack. The performance of the radiator is predicted by the two model-based approaches described above which provide a reliable theoretical basis for the optimization of the thermal management system and the matching of the components.

Startup optimization of gas foil bearings-rotor system in proton exchange membrane fuel cells

Study on the startup-shutdown performance of gas foil bearings-rotor system in proton exchange membrane fuel cells

Numerical Simulation and Optimization of Operating and Structural Parameters for Solid Oxide Fuel Cell

Mathematical modeling and optimization of gas foil bearings-rotor system in hydrogen fuel cell vehicles

Performances investigation and multi-objective optimization of gas foil bearings in hydrogen fuel cell vehicles

Experimental Investigation on the Start-Stop Performance of Gas Foil Bearings-Rotor System in the Centrifugal Air Compressor for Hydrogen Fuel Cell Vehicles

Optimization of purge strategy under fuel cell startup conditions based on CFD-Simulink collaborative simulation

Freeze Start of Proton Exchange Membrane Fuel Cell Systems with Closed-Loop Purging and Improved Voltage Consistency

Impact of the Structural Parameters on the Performance of a Regenerative-Type Hydrogen Recirculation Blower for Vehicular Proton Exchange Membrane Fuel Cells

Experimental study on the static and dynamic performances of gas foil bearings for the centrifugal air compressor used in fuel cell vehicles

An Experimental Investigation of a Microturbine Simulated Rotor Supported on Multileaf Gas Foil Bearings with Backing Bump Foils

Comprehensive performance assessment and multi-objective optimization of high-power proton exchange membrane fuel cell system under variable load

Multi-response Optimization of Ejector for Proton Exchange Membrane Fuel Cell Anode Systems by the Response Surface Methodology and Desirability Function Approach

Investigations on Start-Up Performances of Novel Hybrid Metal Rubber-Bump Foil Bearings

Optimization of fast cold start strategy for PEM fuel cell stack

Coupling Global Parameters and Local Flow Optimization of a Pulsed Ejector for Proton Exchange Membrane Fuel Cells

A Study on Current Overshoot During Start-Ups and Optimal Start-Up Strategy of Proton Exchange Membrane Fuel Cells

Enabling real-time optimization of dynamic processes of proton exchange membrane fuel cell: Data-driven approach with semi-recurrent sliding window method

Microscale structure optimization of catalyst layer for comprehensive performance enhancement in proton exchange membrane fuel cell

Optimization of Membrane Electrode Assembly of PEM Fuel Cell by Response Surface Method

Model-Based Performance Optimization of Thermal Management System of Proton Exchange Membrane Fuel Cell