Abstract:Purpose The purpose of this study, most recent advancements in threedimensional (3D) printing have focused on the fabrication of components. It is typical to use different print settings, such as raster angle, infill and orientation to improve the 3D component qualities while fabricating the sample using a 3D printer. However, the influence of these factors on the characteristics of the 3D parts has not been well explored. Owing to the effect of the different print parameters in fused deposition modeling (FDM) technology, it is necessary to evaluate the strength of the parts manufactured using 3D printing technology. Design/methodology/approach In this study, the effect of three print parameters − raster angle, build orientation and infill − on the tensile characteristics of 3D-printed components made of three distinct materials − acrylonitrile styrene acrylate (ASA), polycarbonate ABS (PC-ABS) and ULTEM-9085 − was investigated. A variety of test items were created using a commercially accessible 3D printer in various configurations, including raster angle (0°, 45°), (0°, 90°), (45°, −45°), (45°, 90°), infill density (solid, sparse, sparse double dense) and orientation (flat, on-edge). Findings The outcome shows that variations in tensile strength and force are brought on by the effects of various printing conditions. In all possible combinations of the print settings, ULTEM 9085 material has a higher tensile strength than ASA and PC-ABS materials. ULTEM 9085 material's on-edge orientation, sparse infill, and raster angle of (0°, −45°) resulted in the greatest overall tensile strength of 73.72 MPa. The highest load-bearing strength of ULTEM material was attained with the same procedure, measuring at 2,932 N. The tensile strength of the materials is higher in the on-edge orientation than in the flat orientation. The tensile strength of all three materials is highest for solid infill with a flat orientation and a raster angle of (45°, −45°). All three materials show higher tensile strength with a raster angle of (45°, −45°) compared to other angles. The sparse double-dense material promotes stronger tensile properties than sparse infill. Thus, the strength of additive components is influenced by the combination of selected print parameters. As a result, these factors interact with one another to produce a high-quality product. Originality/value The outcomes of this study can serve as a reference point for researchers, manufacturers and users of 3D-printed polymer material (PC-ABS, ASA, ULTEM 9085) components seeking to optimize FDM printing parameters for tensile strength and/or identify materials suitable for intended tensile characteristics.

Correlation between the part quality, strength and surface roughness of material extrusion process

Optimization of the extrusion rate for different layer thicknesses to achieve controlled mechanical properties in MEX 3D printing of low-alloy steel

Simultaneous impact of build orientation on mechanical properties, geometrical measurements and surface roughness in material extrusion manufacturing

Systematic Evaluation of Adhesion and Fracture Toughness in Multi-Material Fused Deposition Material Extrusion

Correlation between production parameters and mechanical properties of ABS plus p430 fused deposition material

Analyzing Surface Roughness Variations in Material Extrusion Additive Manufacturing of Nylon Carbon Fiber Composites

Using extrusion-based 3D printing technology to investigate the impact of changing print conditions on tensile characteristics

Design of Experiments to Compare the Mechanical Properties of Polylactic Acid Using Material Extrusion Three-Dimensional-Printing Thermal Parameters Based on a Cyber–Physical Production System

Enhanced Transverse Strength of 3D Printed Acrylonitrile Butadiene Styrene Parts by Carbon Fiber/Epoxy Pin Insertion

Design and optimization methodology for different 3D processed materials (PLA, ABS and carbon fiber reinforced nylon PA12) subjected to static and dynamic loads

Impact of processing defects on microstructure, surface quality, and tribological performance in 3D printed polymers

Synthesis and Investigation of Mechanical Properties of the Acrylonitrile Butadiene Styrene Fiber Composites Using Fused Deposition Modeling

Investigation of the Mechanical Properties, Surface Quality, and Energy Efficiency of a Fused Filament Fabrication for PA6

Investigation and Optimization of Effects of 3D Printer Process Parameters on Performance Parameters

Mechanical Performance over Energy Expenditure in MEX 3D Printing of Polycarbonate: A Multiparametric Optimization with the Aid of Robust Experimental Design

Process Design and Parameters Interaction in Material Extrusion 3D Printing: A Review

Process–Structure–Property Relationship Development in Large-Format Additive Manufacturing: Fiber Alignment and Ultimate Tensile Strength

Mechanical properties evaluation of FFF-printed ABS samples based on different process parameters combined with ANOVA and regression analysis

On Mechanical, Physical, and Bioactivity Characteristics of Material Extrusion Printed Polyether Ether Ketone

Analysis of tensile behavior of Nylon-CF fabricated using material extrusion

The microstructural evolution of material extrusion based additive manufacturing of polyetheretherketone under different printing conditions and application in a spinal implant