Abstract:Polybutylene adipate-terephthalate (PBAT) is a fully biodegradable polyester, which has been proven to be the most suitable alternative to traditional plastics. However, due to the low strength of PBAT (17.2 MPa) and high price, the use of PBAT has a degree of limitations. To obtain a cost-effective and high-performance composite material of PBAT, for this study we selected microcrystalline cellulose, which is inexpensive and easily available, as the reinforcing medium. However, due to the hydrophobicity of PBAT, the mechanical properties of PBAT when mixed with hydrophilic cellulose were low. In order to improve the compatibility of cellulose and PBAT, this study selected hexadecyltrimethoxysilane (HDTMS) containing long carbon chains to silanize microcrystalline cellulose (MCC) to obtain silanized cellulose (SG). Three types of SGs with different degrees of silanization were obtained by controlling HDTMS with different mass ratios (1:10; 3:10; 5:10) to react with MCC. Characterization of these three types of SGs was conducted using FTIR, TEM, and water absorption analysis. The results demonstrated the successful synthesis of SG. With the increase in the reaction ratio of HDTMS and MCC, the size of the nanoparticles increases, and the water absorption decreases significantly. Subsequently, PBAT/SG composites were prepared by blending three kinds of silanized cellulose with PBAT in different proportions by the sol-gel method. To study the thermal stability and compatibility, the mechanical properties of the composites were evaluated, including thermogravimetric testing, scanning analysis, and dynamic thermomechanical testing. The optimal blending ratio and the optimal type of silane cellulose were found. Analysis of the mechanical properties revealed that the tensile strength initially increased and then decreased with increasing blending ratio for all three composites tested. Among them, the PBAT/SG2 composites exhibit superior performance, with a maximum tensile strength reaching 22 MPa at an 85/15 blending ratio, nearly 30% higher than that of pure PBAT alone. The addition of SG significantly improved the strength of the PBAT, and SG2 is more suitable for preparing high-strength composite materials. In addition, after the addition of SG, the yield stress of the composite is improved while maintaining good thermal stability. Both the SEM and DMA results indicated good compatibility of the PBAT/SG composites. This study provides a new idea for the industrial-scale development of degradable polyesters with low cost and good mechanical properties.

Relationship between surfactant content and the properties of microfibrillated cellulose/high density polyethylene composites

Effects of different treatments on the interface and mechanical properties of high density polyethylene reinforced by sericite-tridymite-cristobalite

Interfacial Modiﬁcation and Dispersion of Short Carbon Fiber and the Properties of Composite Papers As Gas Diffusion Layer for Proton Exchange Membrane Fuel Cell (PEMFC)

Effects of Microcapsules Modification on Interfacial Compatibility of Unsaturated Polyester Self-healing Composites

Effects Of Surface Modification Of Self-Healing Poly(Melamine-Urea-Formaldehyde) Microcapsules On The Properties Of Unsaturated Polyester Composites

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Delayed Swelling and Dissolution of Hydrophobically Associated Hydrogel Coatings by Dilute Aqueous Surfactants

Influence of Interfacial Adhesion on Stress-Strain Properties of Highly Filled Polyethylene

Effects of Surface Modifiers on Mechanical and Rheological Properties of Halogen-Free Flame Retarded Polyethylene Composites

Effects of the Content of Silane Coupling Agent KH‐560 on the Properties of LLDPE/magnesium Hydroxide Composites

Effect Of Tdi-Assisted Hydrophobic Surface Modification Of Microcrystalline Cellulose On The Tensile Fracture Of Mcc/Pla Composite, And Estimation Of The Degree Of Substitution By Linear Regression

The effect of chemical composition on microfibrillar cellulose films from wood pulps: water interactions and physical properties for packaging applications

Effects of extractives on some properties of bagasse/high density polypropylene composite

Improving Environmental Stress Cracking Resistance of High‐Density Polyethylene Grades by Comonomer Addition and Nanocomposite Approach

Tailoring the Holocellulose Fiber/Acrylic Resin Composite Interface with Hydrophobic Carboxymethyl Cellulose to Enhance Optical and Mechanical Properties

Evaluation of Mechanical Properties of Composite Material with a Thermoplastic Matrix Reinforced with Cellulose Acetate Microfibers

Identification of percolation threshold of spray‐dried cellulose nanocrystals in homopolymer polypropylene composites

Mechanical properties of sisal fiber reinforced high density polyethylene composites: Effect of fiber content, interfacial compatibilization, and manufacturing process

Enhancement in the Mechanical Properties of in Situ Microfibrillar PLA/POE Composites

Effect of biobased plasticizers, used as dispersing aids, on mechanical, rheological and thermal properties of micro fibrillated cellulose (MFC)/poly (lactic acid) (PLA) biocomposites over the time: how MFC controls the plasticizer migration?

Preparation and Mechanical Properties of PBAT/Silanized Cellulose Composites