Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

A Combined Ordered Macro‐Mesoporous Architecture Design and Surface Engineering Strategy for High‐Performance Sulfur Immobilizer in Lithium–Sulfur Batteries

A Novel Strategy for High-Stability Lithium Sulfur Batteries by in Situ Formation of Polysulfide Adsorptive-Blocking Layer

Defect-Rich Multi-shelled Fe-doped Co3O4 Hollow Microspheres with Multiple Spatial Confinements to Facilitate Catalytic Conversion of Polysulfides for High-Performance Li-S Batteries.

Engineering the Conductive Network of Metal Oxide‐Based Sulfur Cathode toward Efficient and Longevous Lithium–Sulfur Batteries

Coordinated Immobilization and Rapid Conversion of Polysulfide Enabled by a Hollow Metal Oxide/Sulfide/Nitrogen‐Doped Carbon Heterostructure for Long‐Cycle‐Life Lithium‐Sulfur Batteries

Three‐dimensionally Ordered Macro‐porous Metal‐organic Framework for High‐performance Lithium‐sulfur Battery

Synergizing Spatial Confinement and Dual‐Metal Catalysis to Boost Sulfur Kinetics in Lithium–Sulfur Batteries

Engineering the morphology/porosity of oxygen-doped carbon for sulfur host as lithium-sulfur batteries

Rational Construction of Sulfur-Deficient NiCo 2 S 4– x Hollow Microspheres as an Effective Polysulfide Immobilizer toward High-Performance Lithium/Sulfur Batteries

A strategy to achieve high loading and high energy density Li-S batteries

Fast conversion and controlled deposition of lithium (poly)sulfides in lithium-sulfur batteries using high-loading cobalt single atoms

Manipulating Sulfur Mobility Enables Advanced Li-S Batteries

Immobilizing Polysulfide by In Situ Topochemical Oxidation Derivative TiC@Carbon‐Included TiO 2 Core–Shell Sulfur Hosts for Advanced Lithium–Sulfur Batteries

Zinc Tellurium with Anionic Vacancies Anchored on Ordered Macroporous Carbon Skeleton Enabling Accelerated Polysulfide Conversion for Lithium–Sulfur Batteries

Promoting sulfur immobilization by a hierarchical morphology of hollow carbon nanosphere clusters for high-stability Li–S battery

Combined enhanced redox kinetics and physiochemical confinement in three-dimensionally ordered macro/mesoporous TiN for highly stable lithium–sulfur batteries

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Hierarchical Micro‐Nanoclusters of Bimetallic Layered Hydroxide Polyhedrons as Advanced Sulfur Reservoir for High‐Performance Lithium–Sulfur Batteries

Enhanced Polysulfide Regulation <i>via</i> Porous Catalytic V<sub>2</sub>O<sub>3</sub>/V<sub>8</sub>C<sub>7</sub> Heterostructures Derived from Metal-Organic Frameworks toward High-Performance Li-S Batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Laser-induced micro-explosion to construct hierarchical structure as efficient polysulfide mediators for high-performance lithium-sulfur batteries