Abstract:Interfacial layer engineering has been demonstrated as an effective strategy for boosting power output in semiconductor-based dynamic direct-current (DC) generators, although the underlying mechanism of power enhancement remains obscure. Here, such ambiguity has been elucidated by comparing fundamental tribovoltaic DC output characteristics of prototypical metal-oxide-metal heterojunctions prepared by atomic-layer deposition (ALD) with a vertical (out-of-plane carrier transport through the interfacial layer) and a horizontal (in-plane carrier transport along the interfacial layer) configuration such that the influences from nonequilibrium electronic excitation and interfacial capacitive amplification can be individually tuned and investigated. It is found in the case of Al/TiO2/Ti vertical configurations that the open-circuit voltage (VOC) increases linearly from -0.03 to -0.52 V as the thickness of titanium oxide (tTiO2) increases from 0 to 200 nm with a linear amplification coefficient of -2.31 mV nm-1, which is validated by a parallel-capacitor theoretical model with tribovoltaic electronic excitation. In contrast, the VOC output with the horizontal configuration is ∼55 mV, where the potential difference is merely associated with the accumulation of surface charges and the subsequent charge rearrangement in the depletion region. Meanwhile, it is measured that the short-circuit current density (JSC) shows an initial increasing trend when tTiO2 increases, reaches its peak value at 0.21 A m-2 at tTiO2 = 20 nm, and then decreases as tTiO2 increases further. From current-voltage (I-V) characterization, it is proposed that such DC output variation with an optimal interfacial layer thickness stems from the competition of amplified voltage and increased resistance with increasing interfacial layer thickness, with the main charge transport mechanism switching from quantum tunneling to thermionic emission/trap-assisted transport. In contrast, tribovoltaic excitation is proven to be significantly weaker when a wide band-gap insulator (Al2O3) is involved. The elucidation of the fundamental mechanism of power enhancement by the interfacial layer in this work is of great significance in providing instructional direction for the development and optimization of high-performance DC nanogenerators.

Tribovoltaic Effect Promotes Highly Efficient Direct-Current Generator

Tribovoltaic Effect on Metal–Semiconductor Interface for Direct‐Current Low‐Impedance Triboelectric Nanogenerators

A High Strength Triboelectric Nanogenerator Based on Rigid-Flexible Coupling Design for Energy Storage System

Durable Flexible Direct Current Generation through the Tribovoltaic Effect at Contact-Separation Mode

p-n Junction Based Direct-Current Triboelectric Nanogenerator by Conjunction of Tribovoltaic Effect and Photovoltaic Effect

Flexible Textile Direct-Current Generator Based on the Tribovoltaic Effect at Dynamic Metal-Semiconducting Polymer Interfaces

Tribological-behaviour-controlled direct-current triboelectric nanogenerator based on the tribovoltaic effect under high contact pressure

Mechanism of In-Plane and Out-of-Plane Tribovoltaic Direct-Current Transport with a Metal/Oxide/Metal Dynamic Heterojunction

A Dual-Functional Triboelectric Nanogenerator Based on the Comprehensive Integration and Synergetic Utilization of Triboelectrification, Electrostatic Induction, and Electrostatic Discharge to Achieve Alternating Current/Direct Current Convertible Outputs

Study of interfacial design for direct-current tribovoltaic generators

A Rolling‐Mode Al/CsPbBr3 Schottky Junction Direct‐Current Triboelectric Nanogenerator for Harvesting Mechanical and Solar Energy

A Constant Current Triboelectric Nanogenerator Achieved by Hysteretic and Ordered Charge Migration in Dielectric Polymers

Semiconductor-based dynamic heterojunctions as an emerging strategy for high direct-current mechanical energy harvesting

An organic semiconductor/metal Schottky heterojunction based direct current triboelectric nanogenerator windmill for wind energy harvesting

Pursuing Tribovoltaic Effect for Direct-Current Triboelectric Nanogenerator

Sliding mode direct current triboelectric nanogenerators

High Performance Direct Current-Generating Triboelectric Nanogenerators Based on Tribovoltaic P-N Junction with Chcl-Passivaed Csfama Perovskite

Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelectric Nanogenerators to Achieve Significantly Enhanced Triboelectric Performance

Rational design on high-performance triboelectric nanogenerator consisting of silicon carbide@silicon dioxide nanowhiskers/polydimethylsiloxane (SiC@SiO2/PDMS) nanocomposite films

Overall performance improvement of direct-current triboelectric nanogenerator by charge leakage and ternary dielectric evaluation

Ferroelectric‐Polymer‐Enabled Contactless Electric Power Generation in Triboelectric Nanogenerators