Abstract:Discharging improperly treated oily-produced water (OPW) into the environment can have significant negative impacts on environmental sustainability. It can lead to pollution of water sources, damage to aquatic ecosystems and potential health hazards for individuals living in the affected areas. Ceramic hollow fiber membrane (CHFM) technology is one of the most effective OPW treatment methods for achieving high oil removal efficiency while maintaining membrane water permeability. In this study, low-cost calcium bentonite hollow fiber membranes (CaB-HFMs) were prepared from high-alumina calcium bentonite clay with various preparation parameters, including calcium bentonite content, sintering temperature, air gap distance and bore fluid rate. The prepared CaB-HFMs were then subjected to characterization using scanning electron microscopy (SEM), a three-point bending test, porosity, average pore size, hydraulic resistance and flux recovery ratio (FRR) analysis. Statistical analysis employing central composite design (CCD) assessed the interaction between the parameters and their effect on CaB-HFM water permeability and oil removal efficiency. Higher ceramic content and sintering temperature led to reduced porosity, smaller pore size and higher mechanical strength. In contrast, increasing the air gap distance and bore fluid rate exhibit different trends, resulting in higher porosity and pore size, along with weaker mechanical strength. Other than that, all of the CaB-HFMs displayed low hydraulic resistance (<0.01 m2 h.bar/L) and high FRR value (up to 95.2%). Based on CCD, optimal conditions for CaB-HFM were determined as follows: a calcium bentonite content of 50 wt.%, a sintering temperature of 1096 °C, an air gap distance of 5 cm and a bore fluid rate of 10 mL/min, with the desirability value of 0.937. Notably, the optimized CaB-HFMs demonstrated high oil removal efficiency of up to 99.7% with exceptional water permeability up to 535.2 L/m2.h.bar. The long-term permeation study also revealed it was capable of achieving a high average water permeation and a stable oil rejection performance of 522.15 L/m2.h.bar and 99.8%, respectively, due to their inherent hydrophilic and antifouling characteristics, making it practical for OPW treatment application.

Treatment of food processing industries wastewater using a novel Fuller's earth clay-based tubular ceramic membrane.

Treatment of food processing industries wastewaters using a new clay-based inorganic membrane: Performance evaluation and fouling analysis

Evaluation of fuller's earth clay ceramic membrane in treating raw rubber-processing wastewater

Extrusion of Silicon Carbide Based Tubular Membrane Incorporated With Coal Fly Ash and Performance Evaluation in Water Treatment

Development of low-cost ceramic membranes from industrial ceramic for enhanced wastewater treatment

Treatment of textile wastewater using monolayered ultrafiltation ceramic membrane fabricated from natural kaolin clay

Treatment of starch‐rich wastewater using fly ash‐based low‐cost tubular ceramic membrane

Study of the permeability of tubular mineral membranes: application to wastewater treatment

Characterization and Mitigation of the Fouling of Flat-Sheet Ceramic Membranes for Direct Filtration of the Coagulated Domestic Wastewater

Development of clayey ceramic membranes prepared with bio-based additives: Application in water and textile wastewater treatment

Treatment of highly saline effluents laden with organic pollutants using ceramic ultrafiltration membranes and application to leachate treatment

Fabrication and characterization of ceramic tubular composite membranes using slag waste materials for oily wastewater treatment

Characterization and application of novel fly ash blended ceramic membrane in MFC for low-cost and sustainable wastewater treatment and power generation

Remediation of oily-produced water from high-salinity oilfield using a low-cost, high-alumina calcium bentonite hollow fiber membrane

FABRICATION OF CERAMIC, HOLLOW-FIBER MEMBRANE: THE EFFECT OF BAUXITE CONTENT AND SINTERING TEMPERATURE

Treatment of semiconductor-industry wastewater with the application of ceramic membrane and polymeric membrane

Development of a new composite ceramic membrane from mullite, silicon carbide and activated carbon for treating greywater

Elaboration and characterization of novel two-layer tubular ceramic membranes by coating natural zeolite and activated carbon on mullite-alumina-zeolite support: application for oily wastewater treatment

Insights on applications of low-cost ceramic membranes in wastewater treatment: A mini-review

Treating waste with waste: Treatment of textile wastewater using upcycled food waste as a pore-forming agent in the fabrication of ceramic membranes employing DOE/FFD design

Development of Ultrafiltration Kaolin Membranes over Sand and Zeolite Supports for the Treatment of Electroplating Wastewater