Abstract:Abstract To understand the correlation between process, structures, and properties in laser powder bed fusion (L-PBF), it is essential to use numerical analysis as well as experimental approaches. A finite element thermal analysis uses a moving heat source model represented as a volumetric heat flux to simulate heat input by laser. Because of its computational efficiency, finite element thermal analysis is suitable for iterative procedures such as parametric study and process optimization. However, to obtain valid simulated results, the heat source model must be calibrated by comparison with experimental results for each laser scanning condition. The need for re-calibration limits the applicable window of laser scanning conditions in the thermal analysis. Thus, the current study developed a novel heat source model that is valid and precise under any laser scanning condition within a wide process window. As a secondary objective in the development, we quantitatively evaluated and compared the four heat source models proposed to date. It was found that the most suitable heat source model for the L-PBF is conical one among them. Then, a multiple linear regression analysis was performed to represent the heat source model as a function of laser power and scanning velocity. Consequently, the thermal analysis with the novel model is valid and precise within the wide process window of L-PBF.

What problem does this paper attempt to address?

This paper attempts to address the calibration issue of the heat source model under different laser scanning conditions in the Laser Powder Bed Fusion (L-PBF) process. Specifically, existing heat source models need to be recalibrated for each laser scanning condition, which limits their applicability across a wide process window. Therefore, the authors developed a new heat source model aimed at maintaining validity and accuracy under a wide range of laser scanning conditions. Additionally, the paper quantitatively evaluates and compares four existing heat source models to determine which model is most suitable for the L-PBF process. ### Main Research Objectives: 1. **Develop a new heat source model**: This model can maintain validity and accuracy under a wide range of laser scanning conditions without frequent recalibration. 2. **Quantitatively evaluate existing heat source models**: Through experiments and simulations, quantitatively evaluate and compare four existing heat source models to determine which model is most suitable for the L-PBF process. ### Research Background: - **L-PBF process**: L-PBF is a metal additive manufacturing technology that selectively melts and solidifies layers of metal powder using a high-power laser beam to build parts layer by layer. - **Importance of heat source models**: To understand the complex relationships between process, structure, and performance in the L-PBF process, numerical analysis is required. Finite element thermal analysis uses moving heat source models to simulate the heat input from the laser, but existing heat source models need to be recalibrated for each laser scanning condition, limiting their application across a wide process window. - **Existing heat source models**: Commonly used heat source models include conical, linear decay, exponential decay, and double ellipsoidal models. These models have their own advantages and disadvantages but lack a unified evaluation standard. ### Research Methods: 1. **Experimental part**: Bead-on-plate experiments were conducted using nickel-based alloy IN738LC as the model material, with experiments performed on a commercial L-PBF machine. 2. **Calibration of effective absorptivity**: Based on Rosenthal's analytical solution, the effective absorptivity under different laser scanning conditions was determined using the bisection method. 3. **Calibration of shape parameters**: Through finite element thermal analysis and Bayesian optimization, the optimal shape parameter values were iteratively searched. 4. **Multivariable linear regression analysis**: Effective absorptivity and shape parameters were expressed as functions of laser power and scanning speed to eliminate the need for recalibration with each condition change. ### Results and Discussion: - **Experimental results**: Bead-on-plate experiments showed that the depth, width, and area of the fusion zone varied with changes in laser power and scanning speed. - **Calibration of effective absorptivity**: By comparing analytical solutions and experimental results, the effective absorptivity under different laser scanning conditions was successfully calibrated. - **Calibration of shape parameters**: Through Bayesian optimization, the optimal shape parameter values were found, making the simulation results consistent with the experimental results. - **Multivariable linear regression analysis**: Effective absorptivity and shape parameters were successfully expressed as functions of laser power and scanning speed, validating the effectiveness and accuracy of the new model. ### Conclusion: This study successfully developed a new heat source model that maintains validity and accuracy under a wide range of laser scanning conditions without frequent recalibration. Additionally, through quantitative evaluation and comparison, it was found that the conical heat source model is one of the most suitable models for the L-PBF process. This research provides strong support for the optimization of the L-PBF process and the exploration of new materials.

Heat Source Model Development for Thermal Analysis of Laser Powder Bed Fusion Using Bayesian Optimization and Machine Learning

Novel Calibration Strategy for Validation of Finite Element Thermal Analysis of Selective Laser Melting Process Using Bayesian Optimization

Analytical Modelling of Scanning Strategy Effect on Temperature Field and Melt Track Dimensions in Laser Powder Bed Fusion

Pulse approach: a physics-guided machine learning model for thermal analysis in laser-based powder bed fusion of metals

A Gaussian Process-Based extended Goldak heat source model for finite element simulation of laser powder bed fusion additive manufacturing process

Model-Based Sensitivity Analysis of the Temperature in Laser Powder Bed Fusion

Correlating Laser Additive Manufacturing Process with Heat Source Coefficients by Integrated Experimental and Numerical Models

A Physically Motivated Heat Source Model for Laser Beam Welding

On the application of the anisotropic enhanced thermal conductivity approach to thermal modelling of laser-based powder bed fusion processes

A new heat source model for selective laser melting simulations based on energy distribution on the powder layer and the surface of substrate

Heat source models for numerical simulation of laser welding processes – a short review

Physics guided heat source for quantitative prediction of IN718 laser additive manufacturing processes

Global local modeling of melt pool dynamics and bead formation in laser bed powder fusion additive manufacturing using a multi-physics thermo-fluid simulation

Particle-based modelling of laser powder bed fusion of metals with emphasis on the melting mode transition

Development of an Arbitrary Adaptive Volumetric Heat Source Model for Keyhole Mode Laser Welding Process

An empirical model for feedforward control of laser powder bed fusion

New Heat Source Model for Accurate Estimation of Laser Energy Absorption Near Free Surface in Selective Laser Melting

A three-phase model for simulation of heat transfer and melt pool behaviour in laser powder bed fusion process

Analytical modeling of workpiece temperature in laser-assisted milling considering the combined effect of multi-heat sources

On the importance of heat source model determination for numerical modeling of selective laser melting of IN625

An efficient computational approach for heat source optimization in numerical simulations of arc welding processes