Abstract:Laser-textured surfaces enabling reversible wettability switching and improved optical properties are gaining importance in cutting-edge applications, including self-cleaning interfaces, tunable optical lenses, microfluidics, and lab-on-chip systems. Fabrication of such surfaces by combining nanosecond-laser texturing and low-temperature annealing of titanium Ti-6Al-4V alloy was demonstrated by Lian et al. in ACS Appl. Mater. Inter. 2020, 12 (5), 6573-6580. However, it is difficult to agree with (i) their contradictory explanation of the wettability transition due to low-temperature annealing and (ii) their theoretical description of the optical behavior of the laser-textured titanium surface. This comment provides an alternative view-supported by both experimental results and theoretical investigation-on how the results by Lian et al. could be interpreted more correctly. The annealing experiments clarify that controlled contamination is crucial in obtaining consistent surface wettability alterations after low-temperature annealing. Annealing of laser-textured titanium at 100 °C in contaminated and contaminant-free furnaces leads to completely different wettability transitions. Analysis of the surface chemistry by XPS and ToF-SIMS reveals that (usually overlooked) contamination with hydrophobic polydimethylsiloxane (PDMS) may arise from the silicone components of the furnace. In this case, a homogeneous thin PDMS film over the entire surface results in water repellency (contact angle of 161° and roll-off angle of 15°). In contrast, annealing under the same conditions but in a contaminant-free furnace preserves the initial superhydrophilicity, whereas the annealing at 350 °C turns the hydrophobicity "off". The theoretical calculations of optical properties demonstrate that the laser-induced oxide layer formed during the laser texturing significantly influences the surface optical behavior. Consequently, the interference of light reflected by the air-oxide and the oxide-metal interfaces should not be neglected and enables several advanced approaches to exploit such optical properties.

Laser-induced selective wettability transition of 6061 aluminum alloy surfaces

Investigations in the fabrication of surface patterns for wettability modification on a Zr-based bulk metallic glass by nanosecond laser surface texturing

Scalable Wettability Modification of Aluminum Surface through Single-Shot Nanosecond Laser Processing

Fabrication of Functional Surfaces of Aluminum Alloy with a Transition from Superhydrophilic to Superhydrophobic by Nanosecond Laser Irradiation

Laser Textured Dimple-Patterns to Govern the Surface Wettability of Superhydrophobic Aluminum Plates

Nanostructuring of laser textured surface to achieve superhydrophobicity on engineering metal surface

Superhydrophobic Surface Preparation and Wettability Transition of Titanium Alloy with Micro/Nano Hierarchical Texture

Wetting State Transition of Laser Direct Writing Aluminum Surface Based on Coupling Effect of Micro/Nanoscale Characteristics

The effect of surface texturing on the laser-induced wetting behavior of AlSi5 alloy on Ti6Al4V alloy

Superhydrophilicity to Superhydrophobicity Transition of Picosecond Laser Microstructured Aluminum in Ambient Air.

Wettability transition modes of aluminum surfaces with various micro/nanostructures produced by a femtosecond laser

Wettability Transition of Metallic Surfaces from Laser-Generated Superhydrophilicity to Water-Induced Superhydrophobicity Via a Facile and Eco-Friendly Strategy

Comment on "Bioinspired Reversible Switch between Underwater Superoleophobicity/Superaerophobicity and Oleophilicity/Aerophilicity and Improved Antireflective Property on the Nanosecond Laser-Ablated Superhydrophobic Titanium Surfaces"

Parametric investigation of ultrashort pulsed laser surface texturing on aluminium alloy 7075 for hydrophobicity enhancement

Wettability Behaviour of Metal Surfaces after Sequential Nanosecond and Picosecond Laser Texturing

Wettability transition and tribological properties of hydrophobic alloy surfaces prepared by one-step method

Hydrophilic properties of the aluminum alloy induced by femtosecond laser structuring

Reversible Wettability Transition Between Superhydrophilicity and Superhydrophobicity Through Alternate Heating-Reheating Cycle on Laser-Ablated Brass Surface

Fast wettability transition from hydrophilic to superhydrophobic laser-textured stainless steel surfaces under low-temperature annealing

On the laser surface pre-treatment to enhance the surface texture, wettability and adhesion bonding strength of aluminium 7075-T6 laminates

Rapid fabrication of anti-corrosion and self-healing superhydrophobic aluminum surfaces through environmentally friendly femtosecond laser processing