Quasi‐Zero Volume Strain Cathode Materials for Sodium Ion Battery through Synergetic Substitution Effect of Li and Mg

Ming‐Yuan Shen,Jing‐Song Wang,Zhouhong Ren,Tao Wu,Xi Liu,Liwei Chen,Wen‐Cui Li,An‐Hui Lu

DOI: https://doi.org/10.1002/adfm.202303812

IF: 19

2023-06-15

Advanced Functional Materials

Abstract:Theoretical calculations and experimental results show that volume variations are intensively related to two factors, Mg2+ riveted in the Na layer can act as a "pillar" to stabilize the crystal structure and the entry of Li+ into the transition metal (TM) layer can effectively immobilize the coordination oxygen atoms, thus suppressing the slip of P2–O2 transition and enabling a quasi‐zero strain cathode material. P2‐type layered oxide material Na2/3Ni1/3Mn2/3O2 is a competitive candidate for sodium‐ion batteries (SIBs). Nevertheless, it suffers from the strong P2–O2 phase transition during charging to the high voltage regime, rendering drastic volume variations and poor cycling performance. Here, a Quasi‐zero strain P2‐Na0.75Li0.15Mg0.05Ni0.1Mn0.7O2 cathode is synthesized, which reflects the vanishing P2–O2 transition with a volume change as low as 0.49%, thus resulting in the material an excellent cycling performance (83.9% capacity retention after 500 cycles at 5 C). The low‐volume strain can be attributed to two aspects: (1) the Mg2+ riveted in the Na layer can act as a "pillar" to stabilize the crystal structure under the condition of sodium removal, thus restricting the structural changes under high voltage. (2) The entry of Li+ into the transition metal (TM) layer can mitigate the electron localization in the highly desodiation state and can effectively immobilize the coordination oxygen atoms, thus suppressing the slip of P2–O2 transition. This study not only provides a new insight of Li and Mg synergetic substitution effect on the structural stability of P2‐type cathode, but also an efficient avenue for developing cathode materials of SIBs with ultralow bulk strain.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology

What problem does this paper attempt to address?

The paper aims to address the issues of volume change and poor cycling performance of cathode materials in sodium-ion batteries (SIBs) during charge and discharge processes. Specifically, the paper focuses on a quasi-zero volume strain cathode material named P2-Na0.75Li0.15Mg0.05Ni0.1Mn0.7O2 (LMNM). Through the synergistic doping effect of lithium (Li+) and magnesium (Mg2+), this material can suppress the P2–O2 phase transition, thereby significantly reducing volume changes and improving cycling stability.

The core issues of the paper are:
1. **Volume Change Issue**: Traditional P2-type cathode materials undergo a P2–O2 phase transition at high voltage, leading to drastic volume changes, which affect the stability and cycling performance of the material.
2. **Poor Cycling Performance**: Due to the aforementioned volume change issue, traditional cathode materials exhibit poor cycling stability during long-term cycling.

To address these issues, researchers found through theoretical calculations and experimental results that:
- Mg2+ acts as a "pillar" in the sodium layer, helping to stabilize the crystal structure;
- Li+ entering the transition metal (TM) layer can effectively fix the coordinated oxygen atoms, thereby suppressing the P2–O2 phase transition.

Through these methods, the LMNM material exhibits excellent cycling performance, such as maintaining 83.9% capacity retention after 500 cycles at a 5C rate. Additionally, this material has an ultra-low volume change rate (0.49%), which is much lower than other reported nickel-manganese-based materials. These studies not only provide new insights into the synergistic doping effect of Li and Mg but also offer an efficient pathway for developing SIBs cathode materials with ultra-low volume strain.