Abstract:We present a kilogram-scale experiment for assessing the prospects of a novel composite material of metal–organic framework (MOF) and polyacrylates (PA), namely , for trace CO2 capture. Through the interfacial enrichment of metal ions and organic ligands as well as heterogeneous crystallization, the sizes of microporous NbOFFIVE-1-Ni crystals are downsized to 200–400 nm and uniformly anchored on the macroporous surface of PA via interfacial coordination, forming a unique dual-framework structure. Specifically, the composite with a loading of 45.8 wt % NbOFFIVE-1-Ni yields a superior CO2 uptake (ca. 1.44 mol·kg–1) compared to the pristine NbOFFIVE-1-Ni (ca. 1.30 mol·kg–1) at 400 ppm and 298 K, indicating that the adsorption efficiency of NbOFFIVE-1-Ni has been raised by 2.42 times. Meanwhile, the time cost for realizing a complete adsorption/desorption cycle in a fluidized bed has been shortened to 25 min, and the working capacity (ca. 0.84 mol·kg–1) declines only by 1.3% after 2000 cycles. The device is capable of harvesting 2.1 kg of CO2 per kilogram of composite daily from simulated air with 50% relatively humidity (RH). To the best of our knowledge, the excellent adsorption/desorption performances of position it as the most advantageous and practically applicable candidate for trace CO2 capture.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c03661?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c03661</a>.X-ray diffraction (XRD) patterns, FT-IR spectra, N2 adsorption/desorption isotherms, pore size distributions, a table of textural properties, TGA plots of the samples, the CO2 adsorption isotherm XPS spectra, a table of CO2 adsorption heat, images of water drops on the samples, the column breakthrough tests results, the kinetic performance without heat transfer limitation, a table of the kinetics, the dynamic fluidization state of the samples during the fluidized bed test, and the working principle diagram of the fluidized bed (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c03661/suppl_file/am1c03661_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Biomass-derived carbon/MgO-Al2O3 composite with superior dynamic CO2 uptake for post combustion capture application

Regenerable MgO-based Sorbents for CO2 Capture at Elevated Temperature and Pressure: Experimental and DFT Study

Design and development of 3D hierarchical ultra-microporous CO2-sieving carbon architectures for potential flow-through CO2 capture at typical practical flue gas temperatures

Comprehensive Analysis of Biochar-Based Co2 Capture

The Application of Biochar for CO2 Capture: Influence of Biochar Preparation and CO2 Capture Reactors.

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

A High Adsorption Capacity Bamboo Biochar for CO2 Capture for Low Temperature Heat Utilization

Fabrication Of A New Mgo/C Sorbent For Co2 Capture At Elevated Temperature

Systematic study of dynamic CO2 adsorption on activated carbons derived from different biomass

Waste biomass-derived oxygen and nitrogen co-doped porous carbon/MgO composites as superior acetone adsorbent: Experimental and DFT study on the adsorption behavior

A scalable robust microporous Al-MOF for post-combustion carbon capture

Mesoporous Carbon Stabilized MgO Nanoparticles Synthesized by Pyrolysis of MgCl2 Preloaded Waste Biomass for Highly Efficient CO2 Capture.

Microwave-induced preparation of MgO-loaded N-rich porous biochar from marine biomass for efficient CO2 capture and mechanism exploration via theoretical calculation

A Highly Efficient and Stable Composite of Polyacrylate and Metal–Organic Framework Prepared by Interface Engineering for Direct Air Capture

Single-step preparation of activated carbons from pine wood, olive stones and nutshells by KOH and microwaves: Influence of ultra-microporous for high CO 2 capture

Mg and Fe co-loaded biochar prepared by microwave-synergized K 2 FeO 4 of marine biomass for efficient CO 2 capture: Performance assessment and mechanism exploration

Acquiring an Efficient Warm‐CO2 Sorbent from Advanced Pyrolysis of Magnesium Oxalate

Design, characterization and scale-up test of a high performance pre-combustion CO2 adsorbent

Insight into the Co2 Capturer Derived from Graphene/Mgo Composite

Hierarchically Porous Mg-MOF-74/Sodium Alginate Composite Aerogel for CO 2 Capture

Enhanced physical and chemical adsorption of carbon dioxide using bimetallic copper–magnesium oxide/carbon nanocomposite