Abstract:At mesoscale, the blade of micro impeller with Ti-6Al-4V titanium alloy (micro thin wall with mixed boundaries) is a thin-walled structure, characterized by small size, low stiffness, high surface precision, complex boundaries, and difficult-to-control machining deformation. To control and reduce the deformation of micro thin wall, it is necessary to study the micro-deformation mechanisms during milling micro thin-wall parts. In side milling of micro thin wall with mixed boundaries, the micro thin wall suffers from dynamic alternating forces, and the deformation modes are complex, so the direct and accurate theoretical modelling is difficult to make. Since the feed speed in milling micro thin wall is less, the small deformation of micro thin wall can be described based on the flexure deformation model of the thin plate subjected to elastic loadings. Firstly, accompanied by the reciprocal theorem of work for a curved thin plate, Kirchhoff-Love small deformation model of micro thin wall is used to establish the deformation equation and boundary conditions of micro thin wall with mixed boundaries under concentrated milling forces. Thus, the obtained boundary conditions are mainly applied to the subsequent finite element simulation of three-dimensional milling deformation of micro thin wall. Then a three-dimensional deformation simulation of the micro thin wall under different milling parameters is carried out by considering the micro-walled structure, material elasto-plastic constitutive model, the stiffness and geometric structure of micro milling tools in finite element method. In the workpiece constitutive modelling, considering the strain gradient plastic model in micro milling of Ti-6Al-4V titanium alloy, the workpiece plastic constitutive model is modified by introducing the intrinsic characteristic length of the material to describe the size effects in mesoscale micro milling. Finally, a series of the corresponding experiments on the milling of titanium alloy micro thin walls are carried out. By comparing and analyzing the experimental values and finite element numerical results of the micro thin-walled deformation, the micro deformation mechanisms in milling of thin wall are revealed. It also verifies the accuracy and effectiveness of this established milling finite element model of thin wall, and provides theoretical basis and technical support for controlling the milling deformation of micro thin-walled parts.

Study on deformation of titanium thin-walled part in milling process

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Study on Milling Deformation of Aerospace Frame Monolithic Components

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

Numerical Simulation and Analysis of Symmetry and Step-symmetry Milling of Aerospace Thin-walled Workpiece

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Numerical Simulation Study on Milling Force for Aerospace Aluminum Alloy

Three-dimensional numerical simulation for high speed milling of aerospace aluminum alloy

A prediction model for the milling of thin-wall parts considering thermal-mechanical coupling and tool wear

Error Estimation of Titanium Alloy Thin-walled Parts Based on Stiffness Model

Research on Deformation Law and Mechanism for Milling Micro Thin Wall with Mixed Boundaries of Titanium Alloy in Mesoscale

Finite Element Simulation of Bending Thin-Walled Parts and Optimization of Cutting Parameters

Analysis and Optimization of Milling Deformations of TC4 Alloy Thin-Walled Parts Based on Finite Element Simulations

Investigation of the influence of initial residual stress and toolpaths on milling deformation of titanium alloy

Finite Element Simulation and Deformation Control of High-Speed Milling of Al7050-T7451 Thin-walled Parts

602 FEM-based Simulation for Workpiece Deformation in Thin-Wall Milling

Tool Path Planning and Machining Deformation Compensation in High-Speed Milling for Difficult-To-Machine Material Thin-Walled Parts with Curved Surface

Experimental Study on Micromilling Deformation Control of Micro-Thin Wall Based on the Optimal Tool Path

Prediction of Mesoscale Deformation in Milling Micro Thin Wall Based on Cantilever Boundary

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Large Cutting Depth and Layered Milling of Titanium Alloy Thin-Walled Parts