Abstract:This paper presents an experimental and theoretical study of surface generation in the ultra-precision grinding of hard and brittle materials. The study takes into account the material properties, the relative vibration between the grinding wheel and the workpiece, the machining parameters and the phase shift of the grinding process. The Taguchi approach is employed to study the influence of machining parameters on the surface quality and shows that the feed speed and rotational speed of the workpiece are key factors. Experiments have been conducted to study individual variables, and the results further show that the feed rate and the cross-feed distance have a significant effect on surface generation. It is found that the spirals around the central area of the workpiece are the primary mechanism for surface generation, which originates from the synchronous relative tool-work vibration. The integral part of the ratio of the rotational speed of the grinding wheel to rotational speed of the workpiece determines the number of spirals and its fractional part controls the spiral geometry. A theoretical model for predicting the single spiral generation has been developed to explain the accumulation of the phase shift and the geometry. The changeable feed speed near the end of grinding is also modelled, revealing the approximate straight lines around one circle in the central region. The simulated results indicate that the theoretical models and the ground surfaces are in close agreement. The scallop-height model is developed to calculate the influence of phase shift on surface quality, and it is found that the phase shift near the medium value can effectively improve surface quality. Finally, a comparison of different surface generation mechanisms in grinding mould steel, tungsten carbide (WC) and reaction bonded silicon carbide (RB-SiC) is made. It is interesting to note that the Spanzipfel effect contributes to the surface generation not only on ductile materials such as mould steel but also on brittle materials such as WC and RB-SiC. The Spanzipfel effect is the most significant in grinding mould steel. For WC and RB-SiC, the ground surface contains both a ductile region and a brittle region in the form of micro-fractures.

Research on surface generation and forces in ultra-small-grinding (USG) of titanium

Studies on the Surface Quality of the Unsteady-State Grinding Technique

An experimental investigation of system matching in ultrasonic vibration assisted grinding for titanium

Surface Characteristics and Roughness Prediction of TC4 Titanium Alloy in High Speed Grinding

Effect of Ultrasonic Vibration Assisted Grinding Process on Surface Topography and Properties of C/SiC Composite

Theoretical Generalization and Research on the Mechanism of the Unsteady-State Grinding Technique

Surface generation mechanism in ultra-fine microgrinding (UMG) of single crystal silicon considering grinding tool topography

Analytical and experimental study on micro-grinding surface-generated mechanism of DD5 single-crystal superalloy using micro-diamond pencil grinding tool

An experimental and theoretical analysis of surface generation in the ultra-precision grinding of hard and brittle materials

The material removal mechanism and surface characteristics of Ti-6Al-4 V alloy processed by longitudinal-torsional ultrasonic-assisted grinding

Grindability of γ-TiAl intermetallic compounds during ultrasonic vibration-assisted high efficiency deep grinding process

Modeling and experimental study on a deburring method of micro slots of Ti6Al4V tubes with ultra-small-grinding (USG) tool

Process parameter optimization and surface integrity evolution in the high-speed grinding of TiAl intermetallics based on grey relational analysis method

Establishment of dynamic grinding force model for ultrasonic-assisted single abrasive high-speed grinding

Generation Mechanism Modeling of Surface Topography in Tangential Ultrasonic Vibration-Assisted Grinding with Green Silicon Carbide Abrasive Wheel

Micro-Grinding of Electrochemically Pretreated Ultra-high-Chromium Steel

Study of Surface Integrity of Titanium Alloy (TC4) by Belt Grinding to Achieve the Same Surface Roughness Range

Modeling and experimental study of surface generation in ultrasonic vibration-assisted grinding of Ti-6Al-4V micro-channels

Grinding force modeling in ultrasonic-assisted face grinding of ZrO2 ceramics and influence of grinding wheel wear on its accuracy

Research on the effect of grinding force on the axial ultrasonic vibration-assisted grinding of Ti-6Al-4V with multi-grain conical grinding head

Surface and subsurface microscopic characteristics in sapphire ultra-precision grinding