Abstract:Prefabricated structures are widely used because of their advantages of energy savings, environmental protection, standardization, and universality. However, due to the complex structure of the joints, it is easy to make the joint installation difficult and the prefabricated column connection unreliable, and further lead to the poor seismic performance of the structure. Therefore, a new type of dry sleeve joint with double screw sleeve without support is proposed, and the seismic performance and influencing factors of the new dry-sleeve-joint prefabricated column are studied. This study encompasses seven reinforced concrete columns characterized by cross-sectional dimensions of 600 mm × 600 mm. Among these, five specimens feature a novel dry sleeve connection, while the remaining two specimens were entirely cast-in-place. Low-cycle reversed loading experiments were conducted on all specimens to analyze and compare the damage patterns, hysteresis curves, skeleton curves, displacement ductility, energy dissipation capacity, and ultimate bearing capacity between precast and cast-in-place columns. Several parameters, including fabrication method, axial compression ratio, longitudinal reinforcement diameter, and hoop spacing, were examined. The findings demonstrated that the calculated-to-tested ratio of the ultimate bearing capacity for the prefabricated specimens was determined to be 0.62, indicating a high level of safety. The displacement ductility coefficient for each specimen ranged from 2.43 to 3.31, while the ultimate drift ratio was within the range of 1/41 to 1/33, satisfying the specified requirements for seismic performance. However, the hysteresis curve of the prefabricated specimens exhibited a pinching effect, which may be related to the existence of a weak layer on the joint surface of the post-cast section. In general, the shape of the new dry sleeve is maintained in the test, the connection form can effectively transfer the force, and the longitudinal bars can be strained and yield when the prefabricated column reaches the peak load. The new type of dry sleeve connection can be used for longitudinal reinforcement connection of reinforced concrete columns with seismic design.

Emulative and non-emulative prefabricated bridge CFDST columns under eccentric loading

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

Quasi-static Testing and Networked Pseudo-Dynamic Testing on Fiber Reinforced Plastic Retrofitted Reinforcement Concrete Short Columns of Bridge

Behavior of Eccentrically Loaded Large-Scale CFST Slender Columns with Latticed Annular Steel

Global Stability Performance of Multi-Cellular T-Shaped CFST Slender Columns under Eccentric Compression

Innovative Methods to Improve the Seismic Performance of Precast Segmental and Hybrid Bridge Columns under Cyclic Loading

Experimental and numerical study on seismic performance of precast segmental CFST bridge columns with non-uniform prestressed steel tendons

Numerical Study of Concrete-Encased CFST under Preload Followed by Sustained Service Load

Experimental study on the axial compressive behaviour of steel reinforced concrete composite columns with stay-in-place ECC jacket

Cyclic load behaviour of reinforced concrete columns with SMA and ECC in the critical regions

Eccentric compression performance of round-ended CFST slender columns with different aspect ratios

Experimental and Analytical Studies on CFRP Strengthened Circular Thin-Walled CFST Stub Columns under Eccentric Compression

Experimental testing of hybrid sliding‐rocking bridge columns under torsional and biaxial lateral loading

Behavior and Calculation of Tapered Cfdst Columns under Eccentric Compression

RESEARCH ON MECHANICAL PROPERTIES OF WHOLE LIFE CYCLE OF ECCENTRICALLY LOADED CFST COLUMNS

Performance of Round-Ended CFST Columns under Combined Actions of Eccentric Compression and Impact Loads

Numerical modelling of concrete-filled stainless steel slender columns loaded eccentrically

Axial compressive behaviour of thin-walled composite columns comprise high-strength cold-formed steel and PE-ECC

Experimental study on the seismic performance of concrete-filled steel tube columns with a multiple-chamber round-ended cross-section

Experimental Study on Seismic Performance of Prefabricated Columns Connected Using a Novel Dry Sleeve

Numerical Response of Concrete-Filled Steel Tubular (CFST) Columns Externally Strengthened with FRP Composites Subjected to Cyclic Loading