Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Subsurface damage in laser-assisted machining titanium alloys

Surface Formation in Laser-Assisted Grinding High-Strength Alloys

Thermal-Mechanical Effect and Removal Mechanism of Ti-6Al-4V During Laser-Assisted Grinding

Research on material removal of Ti-6Al-4V by laser-belt machining

Mechanical and surface characteristics in laser-assisted machining of NiFeCr alloy: An atomic-scale understanding

Efficient and Low-Damage Machining of Ti6Al4V: Laser-Assisted CBN Belt Grinding

Dislocation Dynamics-Based Modeling And Simulations Of Subsurface Damages Microstructure Of Orthogonal Cutting Of Titanium Alloy

Study on the Heat-Affected Zone, Microstructure, and Surface Quality of TB8 Titanium Alloy Treated by Laser-Assisted Micromachining

Analytical Modeling of Subsurface Damage in Laser-Assisted Machining of Metal Matrix Composites Based on the Reinforcement Fracture Probability

Ablation Characteristics and Interaction Mechanism of Ultra-Fast Pulse Laser-Induced Damage in Titanium Alloy

Simulation and Experimental Analysis of Tool Wear and Surface Roughness in Laser Assisted Machining of Titanium Alloy

A Molecular Dynamics Investigation into the Mechanisms of Material Removal and Subsurface Damage of Nanoscale High Speed Laser-Assisted Machining

Microstructural Strengthening and Plastic Degradation of Ti–6Al–4V Induced by Laser Ablation

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

Milling Force And Surface Topography Of Ti-6Al-4V Titanium Alloy Cladded By The Laser

Influence of Femtosecond Laser Surface Modification on Tensile Properties of Titanium Alloy

Laser Cutting of Titanium Alloy Plates: A Review of Processing, Microstructure, and Mechanical Properties

The influence of cutting parameters on the defect structure of subsurface in orthogonal cutting of titanium alloy

Comparison of Subsurface Damages on Mono-Crystalline Silicon Between Traditional Nanoscale Machining and Laser-Assisted Nanoscale Machining Via Molecular Dynamics Simulation

Atomistic Insight into Laser Shock Peening Response of Α-Titanium: an Experimentally Verified Simulation Study

A Material Removal Model Considering the Effect of Anisotropy on the Processing of Laser Metal Deposition Ti-alloy