Sheath replacement in tendon repair.

A. Hochstrasser,T. R. Broadbent,R. Woolf

1960-07-01

Abstract:

What problem does this paper attempt to address?

Ab Initio Calculation of Structure and Thermodynamic Properties of Zintl Aluminide SrAl2

Zhi-Jian Fu,Li-Jun Jia,Ji-Hong Xia,Ke Tang,Zhao-Hong Li,Xiao-Wei Sun,Qi-Feng Chen

DOI: https://doi.org/10.1515/zna-2015-0250

2015-01-01

Abstract:The structural and thermodynamic properties of the orthorhombic and cubic structure SrAl2 at pressure and temperature are investigated by using the ab initio plane-wave pseudopotential density functional theory methodwithin the generalised gradient approximation (GGA). The calculated lattice parameters are in agreement with the available experimental data and other theoretical results. The phase transition predicted takes place at 0.5 GPa from the orthorhombic to the cubic structure at zero temperature. The thermodynamic properties of the zinc-blende structure SrAl2 are calculated by the quasi-harmonic Debye model. The pressure-volume relationship and the variations inthe thermal expansion a are obtained systematically in the pressure and temperature ranges of 0-5 GPa and 0-500 K, respectively.
Ab Initio Calculations of the Thermodynamics and Phase Diagram of Zirconium

Yan-Jun Hao,Lin Zhang,Xiang-Rong Chen,Ling-Cang Cai,Qiang Wu,Dario Alfe

DOI: https://doi.org/10.1103/physrevb.78.134101

IF: 3.7

2008-01-01

Physical Review B

Abstract:The finite-temperature density-functional theory and quasiharmonic lattice dynamics are used to calculate the Gibbs free energy and quasiharmonic phonons of the hexagonal-close-packed (hcp) and omega (omega) crystal structures for Zr. The hcp phonon dispersions agree with experiment; the omega phonon dispersions have not been measured yet. From the free energy, the volume thermal expansion coefficients of alpha-Zr are predicted. The calculated volume thermal expansion coefficients for alpha-Zr are in good agreement with the experiment data at T>100 K. Our calculated results found that at zero-temperature the lowest-energy phase is not the omega but the hcp phase. This conclusion is in accordance with the result of Schnell and Albers, but in disagreement with those of Ahuja and Jona and Marcus. The predicted phase boundary of alpha ->omega is in good agreement with the available experiment; however, other theoretical results are far from the experiment at high temperatures.
Ab initio and CALPHAD-type thermodynamic investigation of the Ti-Al-Zr system

Z.-X. Deng,D.-P. Zhao,Y.-Y. Huang,L.-L. Chen,H. Zou,Y. Jiang,K. Chang

DOI: https://doi.org/10.2298/jmmb181022039d

2019-01-01

Abstract:Ti?Al based alloys have been widely used in the aeronautics and aerospace. Adding alloying element Zr can significantly improve their high-temperature endurance and corrosion resistance. To investigate the influence of the addition of element Zr on the properties of the Ti?Al system, ab initio calculations and the CALPHAD (CALculation of PHAse Diagrams) method were used to evaluate the Ti?Al?Zr ternary system. Ab initio calculations were carried out to calculate the formation enthalpies of intermetallic compounds and end-members. CALPHAD approach was employed to optimize the thermodynamic parameters based on experiments. The experimental data of phase equilibria at 1073, 1273, 1473, and 1573 K, as well as a vertical section of the Ti3Al?Ti + 5 wt.% Zr were used to assess this system. The thermodynamic parameters of the binary Ti?Al, Al?Zr and Ti?Zr systems were acquired from recent assessments, and the ternary ones were evaluated in the present work. The Ti?Al?Zr ternary dataset has been established and the calculated results are in close agreement with the experimental data on both thermodynamics and phase equilibria.
High‐temperature Mass Spectrometric Study and Modeling of the Thermodynamic Properties of the TiO2‐SiO2‐ZrO2 System

Andrey L. Shilov,Valentina L. Stolyarova,Sergey I. Lopatin,Viktor A. Vorozhtcov,Svetlana A. Kirillova

DOI: https://doi.org/10.1002/slct.202302782

2024-01-17

ChemistrySelect

Abstract:The vaporization processes and thermodynamic properties of the TiO2‐SiO2‐ZrO2 system were studied by Knudsen effusion mass spectrometry (KEMS) at 1973 K. The component activity values obtained by KEMS were optimized within the generalized lattice theory of associated solutions resulting in calculation of the thermodynamic description of the TiO2‐SiO2‐ZrO2 system and its correlation with the structure of the model lattice. Development of the advanced materials based on the TiO2‐SiO2‐ZrO2 system is hindered by lack of the information on its thermodynamic properties and phase equilibria. In the present study, the samples in the TiO2‐SiO2‐ZrO2 system were prepared by solid‐state synthesis and analyzed by X‐ray microanalysis, fluorescence, and diffraction techniques. The thermodynamic properties in this system were evaluated by Knudsen effusion mass spectrometric (KEMS) method and optimized within the generalized lattice theory of associated solutions (GLTAS). The main vapor species over the silica‐containing samples vaporized from the tungsten cell at the temperature 1973 K were SiO, O, WO2, and WO3. The vapor over the samples in the TiO2‐ZrO2 system at 2356 K was composed mainly of TiO, TiO2, O, WO2, and WO3. The activity of components in the samples and the partial pressures of the identified vapor species were determined. At 1973 K, the TiO2‐SiO2‐ZrO2 system is characterized by positive deviations from the ideality. The observed weak dependence of the SiO2 activity on the SiO2 content suggests the presence of a broad field of immiscibility on the phase diagram in the concentration range 40–100 mol . % SiO2. The thermodynamic data on the TiO2‐SiO2‐ZrO2 system obtained by KEMS can be of great value for calculation of the phase equilibria.

chemistry, multidisciplinary
Thermodynamic description of the Al–Ag–Zr system and discovery of the high-strength ternary phase Al1.84Ag0.16Zr

Zixuan Deng,Yanjun Ding,Patrick J. Masset,Kaige Wang,Ligang Zhang,Libin Liu

DOI: https://doi.org/10.1007/s10853-023-08665-3

IF: 4.5

2023-06-22

Journal of Materials Science

Abstract:The investigation of the Al–Ag–Zr system is crucial for the development of heat-resistant Al alloys, which are essential for applications in high-temperature environments. In this work, we first determined the isothermal sections of the Al–Ag–Zr system at 500 and 600 °C using equilibrium alloys. Simultaneously, the τ 3 (Al 6 AgZr 6 ) phase was identified by transmission electron microscopy (TEM). In addition, the three-phase equilibrium of τ 3 + AgZr + (Ag) instead of Al 3 Zr 4 + AgZr + (Ag) was confirmed at 500 and 600 °C. The formation enthalpies of the end-members and ternary compounds in the Al–Ag–Zr system were calculated via first-principles calculations. Based on the experimental and computational results, a thermodynamic database of the Al–Ag–Zr system was established using the CALPHAD (calculation of phase diagrams) method. The hardness of τ 1 (Al 2.68 Ag 0.32 Zr) and τ 2 (Al 1.84 Ag 0.16 Zr) were determined to be 3.82 and 10.20 GPa, respectively, using nanoindentation. The introduction of the τ 2 phase in the design of Al alloys can considerably increase the mechanical properties of the alloys.

materials science, multidisciplinary
High-temperature mass spectrometric study and modeling of ceramics based on the Al2 O3 -SiO2 -ZrO2 system

Valеntina L Stolyarova,Andrey L Shilov,Sergey I Lopatin,Viktor A Vorozhtcov,Dmitrii A Yurchenko,Nikolay B Knyazyan,Goharik G Manukyan

DOI: https://doi.org/10.1002/rcm.9433

2023-02-15

Abstract:Rationale: Materials based on the Al2 O3 -SiO2 -ZrO2 system are promising for a wide range of high-temperature technological applications, such as thermal barrier coatings in the aviation and space industry or advanced materials in nuclear power reactors. Experimental studies of the ceramics based on this system by the Knudsen effusion mass spectrometric (KEMS) method are of significant interest in designing technological processes for the synthesis and exploitation of the Al2 O3 -SiO2 -ZrO2 materials. Methods: Samples of ceramics in the Al2 O3 -SiO2 -ZrO2 system, including the Al2 O3 -ZrO2 and SiO2 -ZrO2 binaries, were prepared by solid-state synthesis. Analysis of the samples was performed by X-ray fluorescence and diffraction techniques. The vapor composition and thermodynamic properties of the components in this system were determined by KEMS. The derived thermodynamic functions were optimized within the generalized lattice theory of associated solutions (GLTAS). Results: In the temperature range 1900-2600 K, the SiO, Al, AlO, Al2 O, ZrO, ZrO2 , and O vapor species were identified over the samples in the systems under study. For the thermodynamic properties to be determined correctly, the samples of the Al2 O3 -SiO2 -ZrO2 system had to be vaporized at temperatures less than 2000 K, where data could be obtained only for the SiO species. The SiO2 activities obtained were taken as the experimental basis for the modeling within the GLTAS approach. This allowed evaluation of the component activities and excess Gibbs energy, and assessment of the relative number of bonds of different types. Conclusions: At 1920 K, the Al2 O3 -SiO2 -ZrO2 system is characterized by negative deviations of its thermodynamic properties from the ideal behavior. The consistency of the obtained modeling results was illustrated by comparison of the values derived from the data for the ternary and the boundary binary systems and thereby indicates the reasonable uniformity of the energy parameters of the lattice model derived in the calculations, which may be used in further modeling of multicomponent systems.
Solidification paths and phase equilibria at 873 and 673 K in the Al-Er-Zr system

Xiaoxu Liu,Yong Du,Bo Jin,Shuhong Liu,Yuling Liu

DOI: https://doi.org/10.1016/j.jallcom.2021.162730

IF: 6.2

2022-03-01

Journal of Alloys and Compounds

Abstract:In the literature, there is only one publication on the experimental isothermal section at 773 K in the Al-Er-Zr system, and no information is available on solidification microstructure in this system. Solidification paths and phase equilibria of the Al-Er-Zr ternary system at 873 and 673 K were thus investigated by means of 14 alloys using X-ray diffraction (XRD), scanning electron microscope (SEM) and electron probe micro analysis (EPMA). Ten primary phases were revealed and two isothermal sections at 873 and 673 K were established in this work. There are fourteen ternary-phase regions at two temperatures and the topology of phase relations is identical at both temperatures. It is found that the maximal solubilities of Er in Al3Zr, Al2Zr, Al3Zr2, AlZr, Al3Zr4, Al2Zr3, AlZr2 and AlZr3 are 2.2 ± 0.1, 4.5 ± 0.2, 9.8 ± 0.5, 11.8 ± 0.6, 8.6 ± 0.3, 6.8 ± 0.3, 4.8 ± 0.2 and 4.4 ± 0.2 at%, respectively. In addition, there are also noticeable solubilities for Zr in Al-Er binary compounds (i.e., Al3Er, Al2Er, AlEr, Al2Er3 and AlEr2), and the maximal solubility of Zr in Al2Er3 is up to 18.0 ± 0.9 at% at 673 K. The phase equilibria and solidification paths in the Al-Er-Zr system determined in the present work provide new experimental data for a future thermodynamic assessment of this system.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Thermal Equations Of State Of The Alpha, Beta, And Omega Phases Of Zirconium

Yusheng Zhao,Jianzhong Zhang,Cristian Pantea,Jiang Qian,Luke L. Daemen,Paulo A. Rigg,Robert S. Hixson,George T. Gray,Yunpeng Yang,Liping Wang,Yanbin Wang,Takeyuki Uchida

DOI: https://doi.org/10.1103/PhysRevB.71.184119

IF: 3.7

2005-01-01

Physical Review B

Abstract:We have conducted synchrotron x-ray diffraction studies on high purity zirconium metal at pressures (P) up to 17 GPa and temperatures (T) up to 973 K. Unit cell volumes (V) were derived from the refinements of x-ray diffraction data for the alpha, beta, and omega phases of zirconium and fitted to a Birch-Murnaghan equation of state with the pressure derivative of the bulk modulus, K-0', fixed at 4.0. The derived thermoelastic parameters for alpha zirconium are isothermal bulk modulus K-0=92(3) GPa, temperature derivative of bulk modulus (partial derivative K/partial derivative T)(P)=-2.3(8)x10(-2) GPa/K, volumetric thermal expansivity alpha(T)=a+bT with a=1.5(+/- 0.8)x10(-5) K-1 and b=1.7(+/- 1.4)x10(-8) K-2, and the pressure derivative of thermal expansion (partial derivative alpha/partial derivative P)(T)=-2.7(9)x10(-6) GPa(-1) K-1. For the beta phase we obtained an isothermal bulk modulus of K-T=66(3) GPa at 973 K and a unit-cell volume of V(973 K)=47.7(3) angstrom(3) at ambient pressure. For the omega zirconium we obtained K-0=90(5) GPa. Within the experimental errors, the K-0 values we determined for the alpha and omega phases and volumetric thermal expansion for the alpha phase are in agreement with previous experimental results, whereas all other thermoelastic parameters represent the first determinations for the three crystalline phases of zirconium metal.
Ab initio inspection of thermophysical experiments for zirconium near melting

M. A. Paramonov,D. V. Minakov,V. B. Fokin,D. V. Knyazev,G. S. Demyanov,P. R. Levashov

DOI: https://doi.org/10.1063/5.0088504

2021-04-28

Abstract:We present quantum molecular dynamics calculations of thermophysical properties of solid and liquid zirconium in the vicinity of melting. An overview of available experimental data is also presented. We focus on the analysis of thermal expansion, molar enthalpy, resistivity and normal spectral emissivity of solid and liquid Zr. Possible reasons of discrepancies between the first-principle simulations and experiments are discussed. Our calculations reveal a significant volume change on melting in agreement with electrostatic levitation experiments. Meanwhile, we confirm a low value of enthalpy of fusion obtained in some pulse-heating experiments. Electrical resistivity of solid and liquid Zr is systematically underestimated in our simulations, however the slope of resistivity temperature dependencies agrees with experiment. Our calculations predict almost constant normal spectral emissivity in liquid Zr.

Materials Science
Thermal Equations of State of Theα,β, Andωphases of Zirconium

Yusheng Zhao,Jianzhong Zhang,Cristian Pantea,Jiang Qian,Luke L. Daemen,Paulo A. Rigg,Robert S. Hixson,George T. Gray,Yunpeng Yang,Liping Wang,Yanbin Wang,Takeyuki Uchida

DOI: https://doi.org/10.1103/physrevb.71.184119

2005-01-01

Abstract:We have conducted synchrotron x-ray diffraction studies on high purity zirconium metal at pressures sPd up to 17 GPa and temperatures sTd up to 973 K. Unit cell volumesVd were derived from the refinements of x-ray diffraction data for thea, b, andv phases of zirconium and fitted to a Birch-Murnaghan equation of state with the pressure derivative of the bulk modulus, K08, fixed at 4.0. The derived thermoelastic parameters for a zirconium are isothermal bulk modulusK0=92s3d GPa, temperature derivative of bulk modulus s]K /]TdP=−2.3s8d310 GPa/K, volumetric thermal expansivity aT=a+bT with a=1.5s±0.8d310−5 K−1 and b=1.7s±1.4d310−8 K−2, and the pressure derivative of thermal expansion s]a /]PdT=−2.7s9d 310−6 GPa−1 K−1. For theb phase we obtained an isothermal bulk modulus of KT=66s3d GPa at 973 K and a unit-cell volume ofVs973 Kd=47.7s3d Å3 at ambient pressure. For the v zirconium we obtainedK0 =90s5d GPa. Within the experimental errors, the K0 values we determined for the a and v phases and volumetric thermal expansion for the a phase are in agreement with previous experimental results, whereas all other thermoelastic parameters represent the first determinations for the three crystalline phases of zirconium metal.
Phase Relationships in the Al-rich Region of the Al-Y-Zr System

X. Bao,L. Liu,S. Huang,Y. Jiang,X. Wang,L. Zhang

DOI: https://doi.org/10.2298/jmmb151011019b

2016-01-01

Journal of Mining and Metallurgy Section B Metallurgy

Abstract:The phase relations in the Al-Y-Zr ternary system at 873 K have been investigated by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) in backscattered electron imaging (BSE) modes. Six three-phase equilibria are determined and no ternary compound is observed. In the meantime, first principle calculations are used to provide theoretical guidance to understand the experimental results.
Measurement of the phase equilibria in the Al–Zr–Y system at 673 and 823 K

Xiaoxu Liu,Yong Du,Shuhong Liu,Yafei Pan

DOI: https://doi.org/10.1016/j.calphad.2019.101726

IF: 2.004

2020-01-01

Calphad

Abstract:Phase equilibria of the Al–Zr–Y ternary system at 673 and 823 K were investigated by using 14 equilibrated alloys, and the two isothermal sections were then established. The phase relations were almost the same at both isothermal sections. There were fourteen ternary-phase regions. Meanwhile, the solubilities of the third element in the binary compounds at both temperatures were discussed. The solid solubilities of Y in all observed Al–Zr binary compounds (i.e., Al3Zr, Al2Zr, Al3Zr2, AlZr, Al3Zr4, Al2Zr3, AlZr2 and AlZr3) were measured, and the solubilities of Y in Al3Zr4 phase reached to 11.9 at% at 823 K. In addition, there were solubilities of Zr in all observed Al–Y binary compounds (i.e., α-Al3Y, Al2Y, AlY, AlY2 and Al2Y3), and the solubility of Zr in AlY2 phase could reach to 13.3 at% at 673 K. The phase equilibria of the Al–Zr–Y ternary system determined by the present work have provided new phase diagram data for a future thermodynamic assessment of this system.
Thermodynamics and kinetics of the oxidation of amorphous Al-Zr alloys

K. Weller

DOI: https://doi.org/10.18419/OPUS-8755

Abstract:During thermal oxidation of binary amorphous AlxZr1-x solid solutions over wide alloycomposition (0.26 ≤ x ≤ 0.68) and oxidation-temperature (350 °C – 560 °C) ranges, a single amorphous ternary oxide phase of well-defined stoichiometry, (Al0.33Zr0.67)O1.83, emerges. The composition of this unexpectedly stoichiometric ternary amorphous oxide phase, that develops instead of the crystalline oxide phases Al2O3 and ZrO2, under conditions far away from genuine thermodynamic equilibrium, is governed by thermodynamics, as demonstrated by thermodynamic assessment, adopting the amorphous (Al0.33Zr0.67)O1.83 phase as a supercooled liquid oxide-oxide (Al2O3-ZrO2) solution phase.

Materials Science
Kinetic Study and Determination of the Enthalpies of Activation of the Dehydrogenation of Titanium- and Zirconium-Doped NaAlH4 and Na3AlH6

T Kiyobayashi,SS Srinivasan,DL Sun,CM Jensen

DOI: https://doi.org/10.1021/jp034543h

2003-01-01

The Journal of Physical Chemistry A

Abstract:The rates of the dehydrogenation of the sodium alanates NaAlH4 and Na3AlH6 doped with 2 mol % Ti or Zr have been measured over the temperature range 363-423 K. NaAlH4 and Na3AlH6 undergo dehydrogenation at equal rates upon direct doping with titanium. However, Na3AlH6 arising from the dehydrogenation of Ti-doped NaAlH4 undergoes dehydrogenation at much slower rates. Rate constants were determined from the slopes of the dehydrogenation profiles. On the basis of Eyring theory, the enthalpies of activation, DeltaH(double dagger), for the dehydrogenation reactions were determined to be similar to100 kJ(.)mol(-1) for both Ti-doped NaAlH4 and Na3AlH6 and similar to135 kJ(.)mol(-1) for both Zr-doped NaAlH4 and Na3AlH6. These results suggest that the dehydrogenation reaction pathways are highly sensitive to the nature and distribution of the dopant but not to differences in the AI-H bonding interactions in [AlH4](-) and [AlH6](3-) complex anions. Furthermore, we conclude that the kinetics are probably influenced by processes such as nucleation and growth and/or range atomic transport phenomenon.
Thermodynamic descriptions of quaternary Mg–Al–Zn–Bi system supported by experiments and their application in descriptions of solidification behavior in Bi-additional AZ casting alloys

Ying Tang,Yongsheng Li,Weimin Zhao,Irina Roslyakova,Lijun Zhang

DOI: https://doi.org/10.1016/j.jma.2020.03.007

IF: 11.813

2020-12-01

Journal of Magnesium and Alloys

Abstract:16 Mg–Al–Zn–Bi quaternary alloys were utilized to measure the phase equilibria and transformation temperatures in the Mg-rich Mg–Al–Zn–Bi quaternary system by means of the X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry techniques. The isothermal section at 400 °C and three vertical sections along Mg–8 wt%Al–0.75 wt%Zn–xBi, Mg–3.4 wt%Al–0.5 wt%Zn–xBi and Mg–6.9 wt%Al–2.3 wt%Zn–xBi in the Mg–Al–Zn–Bi quaternary system were constructed. Based on the literature data, the ternary Mg–Al–Bi and Mg–Bi–Zn systems were re-assessed using the CALculaiton of PHAse Diagram (CALPHAD) approach. The calculated phase equilibria agree well with the measured data. By directly extrapolating the constituent sub-ternary systems, the thermodynamic database for the Mg–Al–Zn–Bi quaternary system was developed. The remarkable consistency between the predicted phase equilibria and the presently measured data in Mg–Al–Zn–Bi quaternary system further demonstrated the accuracy and reliability of the established thermodynamic database. After that, by using the newly developed thermodynamic database, the growth restrict factors and the solidification curves in Bi-containing AZ series magnesium alloys were calculated and analyzed. It was confirmed that the grain size of AZ alloys can be refined with the addition of Bi, and the component Al had larger grain refinement effect than Bi. Besides, the amount of Bi had also noticeable effect on the solidification sequence of the AZ alloys.

metallurgy & metallurgical engineering
New Insights into Solidification and Phase Equilibria in the Al-Al3Zr System: Theoretical and Experimental Investigations

A. V. Khvan,D. G. Eskin,K. F. Starodub,A. T. Dinsdale,F. Wang,C. Fang,V. V. Cheverikin,M. V. Gorshenkov

DOI: https://doi.org/10.1016/j.jallcom.2018.02.023

IF: 6.2

2018-01-01

Journal of Alloys and Compounds

Abstract:Phase equilibria and phase transformations during the solidification of alloys in the Al-Al3Zr corner of the Al-Zr system were investigated using both theoretical ( DFT and Calphad modelling) and experimental techniques. This work involved two separate teams investigating the phase transformations of alloys of different compositions during solidification at slow cooling rates using DTA, SEM, TEM, XRD, EPMA analysis of as-cast and annealed samples. The formation of eutectic type colonies at the boundaries of dendrites and three types of primary intermetallic phase crystals were detected in the examined samples. A eutectic reaction was implied from the results of a DTA analysis. The obtained results question the currently accepted phase diagram for this part of the system which was based on measurements of the solubility of Zr in the aluminium solid solution and the liquidus surface. (c) 2018 Elsevier B.V. All rights reserved.
Dehydrogenation process of titanium and zirconium doped alanates

T Kiyobayashi,T Akita,SS Srinivasan,D Sun,S Sangawa,HT Takeshita,CM Jensen,N Kuriyama

2004-01-01

Abstract:Dehydrogenation process of Ti and Zr doped alanates was studied by means of the thermal gravimetry-differential thermal analysis (TC-DTA) and isothermal dehydrogenation kinetics measurement. With using transmission electron microscope (TEM) equipped with an electron energy loss spectrometer (EELS), we observed the distribution of Ti element on a particle of the Ti doped material. The kinetic measurement showed that: (i) Dehydrogenation of Na3AlH6 proceeds much slower than that of NaAlH4, when the former is observed as a second step of the two step consecutive dehydrogenation of Ti doped NaAlH4. (ii) But if Na3AlH6 is doped directly with Ti, the dehydrogenation rate matches that of NaAlH4. (iii) The activation enthalpies of both Ti doped NaAlH4 and Na3AlH6 are 100 kJ(.)mol(-1), and those of both Zr doped NaAlH4 and Na3AlH6 are 135 kJ(.)mol(-1). These findings imply that the rate determinig step is not related to the cleavage of Al-H bonding, which must be sensitive to whether the species involved is [AlH4](-) or [AlH6](3-), but to a long range phenomenon, such as the diffusion of the atom in the particle. The TEM-EELS observation showed that the Ti element was distributed on the surface of the particle of doped material.
Investigation on Thermal Analysis of Binary Zirconium/Oxidant Pyrotechnic Systems

S. M. Pourmortazavi,S. G. Hosseini,S. S. Hajimirsadeghi,R. Fareghi Alamdari

DOI: https://doi.org/10.1080/00102200802466014

IF: 1.9

2008-10-17

Combustion Science and Technology

Abstract:Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) have been used to examine the thermal behavior of powdered zirconium with some pyrotechnic oxidants, in relation to the behavior of the individual constituents. The results showed that decomposition temperature for pure compounds (potassium nitrate, potassium chlorate, potassium perchlorate, barium nitrate and barium peroxide) are 540, 472, 592, 745 and 600°C, respectively. Pure zirconium powder ignited in air at about 600°C. On the other hand, TG/DTA of Zr/KClO3 indicates that this mixture decomposes at 375°C. Also, when KClO3 is replaced by KClO4 as oxidizer of the fuel, zirconium, the sensitivity of the mixture to thermal ignition will decrease. Zr/KNO3 pyrotechnic mixture has ignition temperature around 427°C. Zr/Ba(NO3)2 pyrotechnic system has a fusion temperature around 625°C and decomposes at 663°C. However, when Ba(NO3)2 is replaced by BaO2 as oxidizer in pyrotechnic mixture containing zirconium, the ignition temperature decreases to 390°C.

energy & fuels,engineering, chemical,thermodynamics, multidisciplinary
Nucleation of L12-Al3M (M = Sc, Er, Y, Zr) Nanophases in Aluminum Alloys: A First-Principles ThermodynamicsStudy

Shuai Liu,Fangjun Liu,Zhanhao Yan,Baohua Nie,Touwen Fan,Dongchu Chen,Yu Song

DOI: https://doi.org/10.3390/cryst13081228

IF: 2.7

2023-08-10

Crystals

Abstract:High-performance Sc-containing aluminum alloys are limited in their industrial application due to the high cost of Sc elements. Er, Zr, and Y elements are candidates for replacing Sc elements. Combined with the first-principles thermodynamic calculation and the classical nucleation theory, the nucleation of L12-Al3M (M = Sc, Er, Y, Zr) nanophases in dilutealuminum alloys were investigated to reveal their structural stability. The calculated results showed that the critical radius and nucleation energy of the L12-Al3M phases were as follows: Al3Er > Al3Y > Al3Sc > Al3Zr. The Al3Zr phase was the easiest to nucleate in thermodynamics, while the nucleation of the Al3Y and Al3Er phases were relatively difficult in thermodynamics. Various structures of Al3(Y, Zr) phases with the radius r < 1 nm can coexist in Al-Y-Zr alloys. At a precipitate's radius of 1–10 nanometers, the core–shelled Al3Zr(Y) phase illustrated the highest nucleation energy, while the separated structure Al3Zr/Al3Y obtained the lowest one, and had thermodynamic advantages in the nucleation process. Moreover, the core–shelled Al3Zr(Y) phase obtained a higher nucleation energy than Al3Zr(Sc) and Al3Zr(Er). Core–doubleshelled Al3Zr/Er(Y) obtained a lower nucleation energy than that of Al3Zr(Y) due to the negative ΔGchem of Al3Er and the negative Al3Er/Al3Y interfacial energy, and was preferentially precipitated in thermodynamics stability.

materials science, multidisciplinary,crystallography
Atomic and electronic structure of amorphous Al–Zr alloy films

J Vegelius,I L Soroka,P T Korelis,B Hjörvarsson,S M Butorin

DOI: https://doi.org/10.1088/0953-8984/23/26/265503

2011-06-13

Abstract:Amorphous Al(73)Zr(27) alloy film, grown and then subjected to heat treatments at 400 and 700 °C, was studied using a combination of x-ray diffraction and soft x-ray spectroscopic techniques. The Al L(2,3) and Al K x-ray absorption spectroscopy (XAS) and Al L(2,3) x-ray emission spectroscopy (XES) used allowed probing the unoccupied and occupied Al 3s, d states and unoccupied Al 3p states in the sample studied. An irreversible transition from amorphous alloy to a mixture of polycrystalline alloy and amorphous alloy, and then to an amorphous oxide phase was observed. After the annealing at 400 °C the Al L(2,3) spectra obtained by XAS could be explained as sums of spectra from amorphous Al(73)Zr(27) alloy and (poly)crystalline Al. This indicates that the sample consists of a mixture of Al-rich crystalline and Zr-enhanced amorphous alloys, as compared to the stoichiometry of the as-deposited Al(73)Zr(27) sample, and that the electronic wavefunctions in the crystalline and amorphous regions can be considered to be confined within the respective regions. The relative amounts of Al atoms were found to be around 1:3 in the crystalline and amorphous phases, respectively, as deduced from the analysis of changes in the electronic structure using Al L(2,3) XAS data. The interpretation was confirmed by the Al K XAS and Al L(2,3) XES. Upon further annealing at 700 °C the polycrystalline phase transformed into amorphous oxide, while the amorphous alloy phase underwent gradual oxidation. The important finding was that the greater part of the sample remained in the amorphous state throughout the temperature regimes described.

Sheath replacement in tendon repair.

Ab Initio Calculation of Structure and Thermodynamic Properties of Zintl Aluminide SrAl2

Ab Initio Calculations of the Thermodynamics and Phase Diagram of Zirconium

Ab initio and CALPHAD-type thermodynamic investigation of the Ti-Al-Zr system

High‐temperature Mass Spectrometric Study and Modeling of the Thermodynamic Properties of the TiO2‐SiO2‐ZrO2 System

Thermodynamic description of the Al–Ag–Zr system and discovery of the high-strength ternary phase Al1.84Ag0.16Zr

High-temperature mass spectrometric study and modeling of ceramics based on the Al2 O3 -SiO2 -ZrO2 system

Solidification paths and phase equilibria at 873 and 673 K in the Al-Er-Zr system

Thermal Equations Of State Of The Alpha, Beta, And Omega Phases Of Zirconium

Ab initio inspection of thermophysical experiments for zirconium near melting

Thermal Equations of State of Theα,β, Andωphases of Zirconium

Phase Relationships in the Al-rich Region of the Al-Y-Zr System

Measurement of the phase equilibria in the Al–Zr–Y system at 673 and 823 K

Thermodynamics and kinetics of the oxidation of amorphous Al-Zr alloys

Kinetic Study and Determination of the Enthalpies of Activation of the Dehydrogenation of Titanium- and Zirconium-Doped NaAlH4 and Na3AlH6

Thermodynamic descriptions of quaternary Mg–Al–Zn–Bi system supported by experiments and their application in descriptions of solidification behavior in Bi-additional AZ casting alloys

New Insights into Solidification and Phase Equilibria in the Al-Al3Zr System: Theoretical and Experimental Investigations

Dehydrogenation process of titanium and zirconium doped alanates

Investigation on Thermal Analysis of Binary Zirconium/Oxidant Pyrotechnic Systems

Nucleation of L12-Al3M (M = Sc, Er, Y, Zr) Nanophases in Aluminum Alloys: A First-Principles ThermodynamicsStudy

Atomic and electronic structure of amorphous Al–Zr alloy films