[The effect of cefoxitin for surgical infections. Especially, the effect for resisted cases to therapy with another cephalosporins (author's transl)].

I. Sakata

1981-07-01

Abstract:

What problem does this paper attempt to address?

In-depth Study of Synergism Between Torrefaction and Catalyst for Balanced Production of Bio-Oil from Rice Husk Pyrolysis Based on Hydrocarbons Production, Energy Yield and Deoxygenation Degree

Yefeng Zhou,Likai Zhu,Shidong Chen,Linchen Fu,Li Cai,Qinhui Wang,Qingang Xiong,Fanghua Xie

DOI: https://doi.org/10.1016/j.biombioe.2022.106494

2022-01-01

Abstract:Previous studies concerning biomass to bio-oil mainly focused on hydrocarbons production, and how to balance the bio-oil production in terms of hydrocarbons production, energy yield and deoxygenation degree is a challenging issue. After the pretreatment of torrefaction, catalytic fast pyrolysis (CFP) was performed at two-zone fixed-bed reactor. The synergism between torrefaction and catalyst during torrefaction-catalytic fast pyrolysis (T-CFP) was investigated for the balanced production of bio-oil from rice husk. Firstly, the results of two catalysts (ZrO2/n-ZSM-5 and ZrO2/n-ZSM-5/attapulgite) indicated that the catalyst with the incorporation of attapulgite (ATP) could realize the balance between the acid and basic sites, which resulted in deeper deoxygenation. Then, the results of torrefaction-catalytic pyrolysis showed that, among three torrefaction temperatures adopted, mild torrefaction (210 degrees C) had better synergistic effects with both catalysts. Specifically, catalytic pyrolysis of biomass after mild torrefaction over both catalysts realized the enhancement of deoxygenation degree and energy yield. Moreover, with the pretreatment of mild torrefaction, the performance of ZrO2/n-ZSM-5/ATP turned out to be obviously superior to ZrO2/n-ZSM-5 in terms of hydrocarbons production (7.5% > 0.8%) and deoxygenation mode. Therefore, the combination of ZrO2/n-ZSM-5/ATP and mild torrefaction could achieve more balanced production of bio-oil from T-CFP process.
Co-pyrolysis of sewage sludge and lignocellulosic biomass: Synergistic effects on products characteristics and kinetics

Yang Liu,Yongmeng Song,Jie Fu,Wenya Ao,Asif Ali Siyal,Chunbao Zhou,Chenglong Liu,Mengyan Yu,Yingwen Zhang,Jianjun Dai,Xiaotao Bi

DOI: https://doi.org/10.1016/j.enconman.2022.116061

IF: 10.4

2022-09-15

Energy Conversion and Management

Abstract:Co-pyrolysis of sewage sludge (SS) and corn stalk (CS) was conducted, followed by various online and offline analyses of pyrolysis products and reaction kinetics. Significant synergistic effects were found with the addition of CS to SS: the char yield decreased while the bio-oil yield increased significantly, and CO and CH4 yields increased. The sequential response order of functional groups in bio-oil to CS percentage is: alcohols → ketones → alkanes. The interaction of SS and CS significantly promoted the production of phenols and furans while inhibited the production of oxygen heterocycles and nitrogen compounds, which was beneficial for the subsequent utilization of bio-oil. The addition of CS to SS significantly increased the carbon content while reduced the sulfur content in the char. Activation energy (Ea) of the mixture was assessed by two iso-conversional methods, and Flynn-Wall-Ozawa (FWO) always had a higher correlation to the reaction than Kissinger-Akahira-Sunose (KAS). Average Ea of SS (604.42 and 631.76 kJ/mol) was higher than that of CS (251.18 and 258.05 kJ/mol), which implied that the addition of biomass was beneficial for SS pyrolysis. The pre-exponential factor was ≥1010 s−1, suggesting that the reactions occurring in co-pyrolysis were the loose junctional complex (simple complex) in nature. The co-pyrolysis of SS and CS followed the power law model reaction mechanism (P3). The synergistic effects were mainly caused by the radicals (e.g., H, HO, CH3, OCH3) formed from the devolatilization of CS and the metallic elements (e.g., Al, Fe, Ca, Mg, K) present in SS. The research findings provided practical and new insights into a cleaner and more efficient co-pyrolysis strategy.

energy & fuels,thermodynamics,mechanics
Thermogravimetric characteristics of corn straw and bituminous coal co-pyrolysis based the ilmenite oxygen carriers

Pengxing Yuan,Xiude Hu,JingJing Ma,Tuo Guo,Qingjie Guo

DOI: https://doi.org/10.1016/j.cjche.2023.12.013

IF: 3.8

2024-01-13

Chinese Journal of Chemical Engineering

Abstract:Herein, the co-pyrolysis reaction characteristics of corn straw (CS) and bituminous coal in the presence of ilmenite oxygen carriers (OCs) are investigated via thermogravimetry coupled with mass spectrometry. The results reveal that the participation of OCs weakens the devolatilization intensity of co-pyrolysis. When the CS blending ratio is < 50%, the mixed fuel exhibits positive synergistic effects. The fitting results according to the Coats-Redfern integral method show that the solid-solid interaction between OCs and coke changes the reaction kinetics, enhancing the co-pyrolysis reactivity at the high-temperature zone (750–950 °C). The synergistic effect is most prominent at 30% CS blending ratio with co-pyrolysis activation energy being in the range 26.35–40.57 kJ·mol –1 . Graphical abstract Download : Download high-res image (287KB) Download : Download full-size image

engineering, chemical
Synergistic effects, gas evolution and ash interaction during isothermal steam co-gasification of biomass with high-sulfur petroleum coke

Xin Yu,Dunxi Yu,Fangqi Liu,Jingkun Han,Jianqun Wu,Minghou Xu

DOI: https://doi.org/10.1016/j.energy.2021.122840

IF: 9

2022-02-01

Energy

Abstract:This work investigated the co-gasification behavior of rice straw (RS) and a high-sulfur petroleum coke (PC). An isothermal gasification experiment under a steam atmosphere was conducted on a self-designed thermogravimetry (TG) coupled with mass spectrometry (MS). The results indicate that the high sulfur content in PC seem to have no significant effect on co-gasification. RS showed obvious catalytic effect only after it was completely gasified into ash. Affected by the high concentration of steam, the main components of synthesis gas are H2 and CO2. The RS ash presents a violent melting state, and the lower RS addition ratio only shows a strong catalytic effect in the initial stage of the reaction. The high addition ratio makes the ash particles in the liquid phase contact and react well with the PC particles, and will not inhibit the gasification of the PC particles before the PC particles are completely wrapped.

energy & fuels,thermodynamics
Experimental study on co-pyrolysis of petroleum coke and coals: Synergy effects and co-gasification reactivity

Jilin Li,Yifei Wang,Longchu Zhu,Zhifeng Zhang,Huixia Xiao

DOI: https://doi.org/10.1016/j.fuel.2020.118368

IF: 7.4

2020-11-01

Fuel

Abstract:In this work, the co-gasification reactions of petroleum coke and three Chinese coals were carried out using a thermogravimetric analyzer (TGA) to investigate the influences of blend ratio, coal rank, coal ash and coal char types (in situ formed char and preprepared char) on the synergy effects and co-gasification reactivities during co-gasification. Due to the difference of particle size distribution, petroleum coke particles were filtered from blended chars and tested using a Raman spectrometer and a scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDX). The results indicated that the gasification reaction rate of unreactive petroleum coke was enhanced through co-processing with low rank coals. For preprepared coal char, the catalytic effect of alkaline and alkaline earth metals (AAEMs) of coal ash was the main synergy effect. The in situ formed coal char presented a more significant synergy effect on the enhancement of reaction rate of petroleum coke, which was caused by the carbon structural changes of unreactive petroleum coke particles in co-pyrolysis process, such as less ordered carbon structure, lower graphitization degree, more amorphous carbon structure and more carbon active sites. Moreover, the SEM-EDX results also indicated that significant interactions existed during co-pyrolysis of petroleum coke char and in situ formed coal char.

energy & fuels,engineering, chemical
Synergistic effect of co-pyrolysis of tea seed shells and scrap tyres and product evaluation

Shaobo Ouyang,Cong Zhu,Yong Xia,Yu Yang,Caixia Zhang,Chi-Wing Tsang,Daolin Xiong,Liqing Li,Kai Yang

DOI: https://doi.org/10.1007/s13399-022-03617-4

IF: 4.05

2022-12-13

Biomass Conversion and Biorefinery

Abstract:The co-pyrolysis behaviors of tea seed shell (TSS) and scrap tyre (ST) were studied systematically to discuss the potential synergistic effect. The thermogravimetric characteristics of TSS, ST, and their blends were investigated under various heating rates. The results obtained showed that a significant synergetic effect existed during the co-pyrolysis of the blends, in which the experimental mass loss curves were significantly lower than the calculated curves. Increasing the heating rate of blends led to the increase of reaction temperature due to heat transfer hysteresis. According to the TG data, the kinetics parameters of the co-pyrolysis process were calculated by Coats-Redfern method. The activation energies of the pyrolysis of TSS and ST were from 68 to 81 kJ·mol −1 and 59 to 63 kJ·mol −1 , respectively. The activation energies range of the blends were 44–54 kJ·mol −1 using the first-order reaction kinetics model, and 56–64 kJ·mol −1 using the 1.5-order reaction kinetics model, respectively. The co-pyrolysis of the blends required lower activation energy than that of TSS and ST alone, and the energy required for co-pyrolysis reaction decreased with the increase of TSS ratio. Based on the results of DTG, the co-pyrolysis characteristics of TSS and ST in a fixed-bed reactor were further discussed, and the effects of operation parameters, (e.g., mass ratio of TSS to ST, pyrolysis temperature, and residence time), on product distribution and composition were investigated in detail. The results obtained showed that the experimental yields of liquid and solid were higher than that of the theoretical values, corresponding to a lower experimental gas yield, further confirming the existence of synergistic effect during the co-pyrolysis process. By analyzing the composition of liquid derived from co-pyrolysis of the blend within 40 wt.% TSS, it was found that there was a significant difference between the experimental and theoretical values, and the products containing oxygen and nitrogen were significantly reduced.

energy & fuels,engineering, chemical
Thermogravimetric-infrared analysis and performance optimization of co-pyrolysis of oily sludge and rice husks

Guiying Xu,Xinghui Cai,Li Wang,Qi Zhang,Baizeng Fang,Xiaohan Zhong,Jingang Yao

DOI: https://doi.org/10.1016/j.ijhydene.2022.06.099

IF: 7.2

2022-07-16

International Journal of Hydrogen Energy

Abstract:In this paper, thermogravimetric-infrared spectroscopy was used to analyze co-pyrolysis of oily sludge (OS) from oil penetration and rice husks (RH) at various ratios (1:0; 3:1; 1:1; 1:3; 0:1), obtaining pyrolysis weight-loss behaviors, the laws of mutual synergy, and gas volatilization characteristics. The Coats-redfern and response surface method were employed to analyze kinetics and optimize pyrolysis, respectively. The T i , T max , and T f increase as the heating rate increases, and the weight loss increases in the second stage. With the increase of the proportion of RH, the T i and T max of the mixture increase, while the T f and residual content decrease. The co-pyrolysis of the OS and RH has synergistic effects. The addition of RH is beneficial to reduce the E of OS pyrolysis. The mixing ratio affects the strength of small-molecular-gases volatilization. When the RH ratio is 58.9% at 10K/min, the minimum predicted E and residual amount of co-pyrolysis are 58.602 kJ/mol and 42.6%, respectively.

energy & fuels,electrochemistry,chemistry, physical
Synergistic effect on thermal behavior and product characteristics during co-pyrolysis of biomass and waste tire: Influence of biomass species and waste blending ratios

Miaomiao Niu,Rongyue Sun,Kuan Ding,Haiming Gu,Xiaobo Cui,Liang Wang,Jichu Hu

DOI: https://doi.org/10.1016/j.energy.2021.122808

IF: 9

2022-02-01

Energy

Abstract:The work aims to get a full understanding of the co-pyrolysis synergy between different biomass and waste tire for high value utilization of both biomass and waste tire. Rice husk (RH), wheat straw (WS) and moso bamboo (MB) were chosen to co-pyrolyze with waste tire (WT). Influence of biomass species and blending ratios on co-pyrolysis synergistic effect was studied by analyzing thermal behavior, product yields and character. Thermogravimetry analysis proved the existence of synergistic effect and measured positive decomposition synergy for MB/WT. Char production showed little synergy for all biomass during co-pyrolysis while positive synergistic effect in liquid production was weakened with WT blending. Co-pyrolysis char integrated both biomass char and WT char characteristic. The pore structure was corresponding to that of biomass char and improved by synergy for all biomass, especially WS and MB. Co-pyrolysis oil mainly consisted of the typical components of bio-oil and WT oil, showing lower oxygenated compounds percentage than bio-oil. Aromatic hydrocarbons formation was inhibited while alicyclic hydrocarbons formation was intensified by co-pyrolysis interaction and MB/WT co-pyrolysis showed significant synergy in ethers and furans production. Co-pyrolysis showed positive synergistic effect on CO and CO2 generation and negative synergistic effect on H2 and CH4 content.

energy & fuels,thermodynamics
Infrared heating and synergistic effects during fast co-pyrolysis of corn stover and high alkali coal

Chenhao Li,Zuohua Liu,Erfeng Hu,Jianglong Yu,Chongyang Dai,Yishui Tian,Yang Yang,Yongfu Zeng

DOI: https://doi.org/10.1016/j.psep.2023.09.033

IF: 7.8

2023-11-01

Process Safety and Environmental Protection

Abstract:Infrared heating method aids in the investigation of the primary volatiles-volatile interactions during co-pyrolysis by minimizing the secondary reactions. In this study, characteristics and synergistic effects during the rapid co-pyrolysis of high alkali coal (HAC) and corn stover (CS) using infrared heating were systematically investigated. The co-pyrolysis liquid yield initially increased and then decreased with increasing the pyrolysis temperature. The synergistic effects clearly promoted the tar yield and quality. The co-pyrolysis tar yields increased with rising temperature, from 23.29 wt% at 500 °C to 28.87 wt% at 700 °C, before decreasing to 23.57 wt% at 800 °C. At 700 °C, the largest deviation was 63%. Moreover, the co-pyrolysis interaction had a maximal negative deviation of − 35% for CO2 mass at 700 °C, indicating that the co-pyrolysis of CS and HAC reduced carbon emissions. The tetracyclic and tricyclic aromatic hydrocarbons in PAHs were substantially reduced due to CS hydrogen radicals, and the quantities of the binary aromatic rings decreased by 50% with the increase in temperature. The presence of AAEMs in coal affected the bond breaking and reformation of molecular bonds within the tar components. Raman analysis and BET analyses suggested that AAEMs in HAC enhanced the reactivity of char. The interaction between the volatile of CS and HAC increased the amount of ammonia carbon and the number of active sites.

engineering, environmental, chemical
Synergistic effect of Hami coal and polystyrene on products properties during co-pyrolysis: Evaluation on the contribution of different interaction sources

Tingting Zhang,Zongqing Bai,Zhenxing Guo,Lingxue Kong,Haoyu Dou,Jin Bai,Wen Li

DOI: https://doi.org/10.1016/j.fuel.2022.127209

IF: 7.4

2022-12-30

Fuel

Abstract:Co-pyrolysis with low rank coal is an important way to treat waste plastics and recycle them into valuable materials. Complex interactions between volatiles-feedstock, volatiles-volatiles, and volatiles-char co-exist during co-pyrolysis, which will influence the synergistic effects and have not been extensively understood. In this work, some new feedstock configurations were conducted in a fixed-bed reactor to explore the contribution of these complicated interactions between different sources to the synergy effect observed during co-pyrolysis of Hami coal (HM) and polystyrene (PS). Results show that the interaction between PS-volatiles and HM-volatiles is found to be a dominant contributor to tar lightening in co-pyrolysis, which accounts for 5.67 wt% increase in the content of gasoline fractions (<180 °C) compared to the theoretical calculated value. Meanwhile, the content of gasoline fractions in tar increases with the enhancement of the interaction between volatiles and unreacted-HM. The volatiles and unreacted-HM interaction is the main contributions to synergy in aromatization of char, while the PS-volatiles and HM-char interaction plays an opposite role. The co-pyrolysis of HM-char locating on the top of PS also reveals the catalytic activity of HM-char on PS decomposition. Furthermore, the interaction between unreacted-HM and PS-melt is not conducive to the production of gas, but favorable to the production of char with high aromaticity. These results provide a valuable supplement for the understanding of the interaction mechanisms during co-pyrolysis, and also help to enhance synergistic pathways of the target products while simultaneously reducing inhibitory interactions.

energy & fuels,engineering, chemical
Co-pyrolysis of low-rank coal and rice stalk: A comprehensive study on product distributions, product properties, and synergistic effects

Youwei Zhi,Donghai Xu,Shaoyan Sun,Mingyan Ma,Huanteng Liu,Lijie Yang,Jun Zhao

DOI: https://doi.org/10.1016/j.jaap.2024.106434

IF: 6

2024-03-01

Journal of Analytical and Applied Pyrolysis

Abstract:Co-pyrolysis of low-rank coal and rice stalk is an important way to achieve hierarchical and efficient utilization of energy. This work explored how blend ratios (0–100 wt%) and temperatures (773–1073 K) affect pyrolysis product distribution and characteristics. The results showed that a higher rice straw ratio (80 wt%) significantly reduced the yield of char (22.38–26.9 wt%) compared with 20 wt% of rice straw at different temperatures. The yield and physicochemical properties of target products were closely related to process parameters, which can provide a promising opportunity to acquire desired products by reaction conditions optimization. Co-pyrolysis was able to inhibit the production of large aromatic ring structures in char. High temperature promoted the generation of cross-linked structures, which was influenced by the blend ratio. The synergistic effects of BET surface area and pore volume were most pronounced when the J content was 40 wt% at 873 K, and their increments were 59.6 m2/g and 0.027 cm3/g, respectively. For the char derived from lower rice straw proportions (0, 20, and 40 wt%), the main combustion range and the maximum combustion rate temperature showed a progressive shift towards higher values with temperature increasing. The research is valuable of guiding high-value utilization of agricultural residues and energy transitions.

engineering, chemical,chemistry, analytical,energy & fuels
A TG-IR study on the co-pyrolysis characteristics of oily sludge and crops

Hui Rong,Jiangru Yuan,Yinqi Feng,Yufeng Yi,Zheng Chang

DOI: https://doi.org/10.1007/s13399-020-00969-7

IF: 4.05

2020-09-03

Biomass Conversion and Biorefinery

Abstract:The co-pyrolysis characteristics of oily sludge (OS), wheat straw (WS), peanut straw(PS), and coconut shell (CS) have been studied experimentally with the thermogravimetric infrared analyzer, and the precipitation characteristics of the main reaction products were analyzed. During the separate pyrolysis of OS, the main weight loss stage appeared in 200–500 °C and the maximum weight loss peak appeared at 460 °C; its value is 8.42%/min. For the three additives, the main weight loss stage of all the three additives appeared in 200–400 °C; the maximum weight loss peak values of WS, PS, and CS were 11.38%/min, 8.77%/min, and CS 12.03%/min, respectively. It has been found that the three additives promoted the pyrolysis reaction of OS, and the mean apparent activation energy of the reaction was significantly reduced when the content of WS was 40%, PS was 40%, and CS was 50%. WS and PS make the pyrolysis process more adequate, and the amount of residual material is reduced. The addition of three additives could reduce the production of CH4 and CO and increase the precipitation of CO2.

energy & fuels,engineering, chemical
Co-pyrolysis of different torrefied Chinese herb residues and low-density polyethylene: Kinetic and products distribution

Shengxiong Huang,Jie Qin,Tao Chen,Cheng Yi,Siyan Zhang,Zhi Zhou,Nan Zhou

DOI: https://doi.org/10.1016/j.scitotenv.2021.149752

2022-01-01

Abstract:In present work, the synergistic effects during co-pyrolysis of low-density polyethylene (LDPE) and torrefied Chinese herb residues (CHR) have been investigated by thermogravimetric analysis. The kinetic parameters of co-pyrolysis were calculated by Coats-Redfern method, and the difference values of experiment and theoretical were also investigated for gas and oil compounds. The results show that the extent of synergistic or inhibitory effects of co-pyrolysis was connection with the severity of CHR torrefaction, and the activation energy depend on the blend ratio of LDPE and CHRs. In addition, co-pyrolysis tends to generate more small molecule products and reduce oil yield, and increase the CO content but decreases CH4 in the gas product. The results also found that the liquid products have a significant interaction during the co-pyrolysis process, because the content of aliphatic hydrocarbons and alcohols in the blends pyrolysis oil has been greatly increased, and improving the quality of oil.

environmental sciences
Physicochemical synergistic effect of microwave-assisted Co-pyrolysis of biomass and waste plastics by thermal degradation, thermodynamics, numerical simulation, kinetics, and products analysis

Yujun Ma,Wenliang Wang,Hui Miao,Sizhe Han,Yishuai Fu,Yutong Chen,Jiaqi Hao

DOI: https://doi.org/10.1016/j.renene.2024.120026

IF: 8.7

2024-01-24

Renewable Energy

Abstract:Understanding the physicochemical synergistic effect of microwave-assisted co-pyrolysis (MACP) of biomass and waste plastics is crucial for efficient conversion and improving the quality of bio-oil. Thermal degradation , thermodynamics, and numerical simulation of co-pyrolysis of the corncob (CC) and polystyrene (PS) were conducted. Results showed that the co-pyrolysis of CC and PS had a positive physical synergistic and compatible effect in reducing energy consumption and accelerating reaction rate. The reaction kinetics analysis and pyrolysis products analysis found that the co-pyrolysis of CC and PS had a positive chemical synergistic effect. The co-pyrolysis both effectively reduced the pyrolysis activation energy and improved the yield and quality of bio-oil. Significantly, the sample of CC/PS (1:2) had the highest yield of bio-oil (52.3 wt%) and the highest relative content of aromatics (95.0 area%) in co-pyrolysis, while 450 °C was the most ideal pyrolysis temperature. This work indicated that the MACP of CC and PS showed a positive physicochemical synergistic effect, and provided theories and approaches for the production of bio-oil from the biomass and waste plastics by MACP.

energy & fuels,green & sustainable science & technology
Investigation on the characteristics and interaction of co-pyrolysis of oil shale and peanut shell

Shuang Cui,Tianhua Yang,Yingmei Zhai,Yiming Zhu,Ziqi Yu,Xingping Kai

DOI: https://doi.org/10.1016/j.fuel.2023.127502

IF: 7.4

2023-01-21

Fuel

Abstract:Aiming at the low oil yield of oil shale, and the high content of oxygen in biomass pyrolysis oil, the co-pyrolysis of oil shale and peanut shell were studied by thermogravimetric analyzer and fixed bed reactor. Based on the co-pyrolysis characteristics, kinetic and oil phase products analysis, a series of co-pyrolysis interaction mechanism has been proposed. The co-pyrolysis caused the earlier decomposition of oil shale and higher conversion rate of blended feedstock. The contribution of co-pyrolysis to the total conversion and oil phase products yield was most significant with biomass blending ratio of 50 %, while the contribution to the activation energy and the generation of aliphatic hydrocarbons was most significant when the ratio was 25 %. The co-pyrolysis interaction at low-temperature (160–400 °C) is dominated by oil shale radicals promoting biomass bond breaking and the minerals catalysis on biomass decomposition. For high-temperature (400–600 °C), it is dominated by biomass alkali/alkaline earth metals which catalyze oil shale decomposition. The interaction promotes the formation of aliphatic and aromatic hydrocarbons in the oil, reduces the average carbon chain length and increases the light oil content.

energy & fuels,engineering, chemical
Synergetic Effect of Co-pyrolysis of Cellulose and Polypropylene over an All-Silica Mesoporous Catalyst MCM-41 Using Thermogravimetry–Fourier Transform Infrared Spectroscopy and Pyrolysis–Gas Chromatography–Mass Spectrometry

Junjie Xue,Jiankun Zhuo,Mi Liu,Yongchao Chi,Dahu Zhang,Qiang Yao

DOI: https://doi.org/10.1021/acs.energyfuels.7b01651

IF: 4.6541

2017-01-01

Energy & Fuels

Abstract:Biomass is one of the promising alternative materials to solve the energy and environmental crisis. Fast pyrolysis is one of the most economical and commercially realizable technologies to convert biomass to useable fuels and chemicals. To improve the liquid products, co-pyrolysis with polypropylene (PP) over a mesoporous catalyst MCM-41 was studied in this paper. Thermogravimetry Fourier transform infrared spectroscopy (TG-FTIR) and pyrolysis gas chromatography mass spectrometry (Py-GC MS) were used as the main analysis methods to study the mass loss and detailed products of the co-pyrolysis. The mass loss, main functional groups, and identified products of pyrolysis of cellulose, PP, and their mixture were analyzed and discussed. All of the TG, FTIR, and Py-GC MS data show that there is no significant synergism between cellulose and PP when simply mixing them, although the C/H-eff of the mixture increases from 0 to 1.3. However, the addition of MCM-41 bring significant synergism. The TG and differential thermogravimetry (DTG) data show that the co-pyrolysis with MCM-41 shifts the decomposition of PP to a lower temperature, which provides more overlap between cellulose and PP in the range of 300-400 degrees C. According to the FTIR spectra, CO, CO2, and carbonyl are also produced in the peak for pyrolysis of PP for the mixture together with MCM-41, which indicates the intermolecular synergetic reaction. Furthermore, the results from Py-GC MS show that olefins (43.9%), oxygenated compounds (24.8%, mainly alcohols), and aromatics (17.8%) are the main products of co-pyrolysis of cellulose and PP in the presence of MCM-41, while oxygenated compounds (82.2%, mainly saccharides), olefins (4.7%), and aromatics (1.1%) will be the main products without the catalyst. Olefins and alcohols are Much more than the calculated value, which is the main result of synergism. Alcohols are mainly produced from the radical from the cracking of PP combined with the hydroxyl radical produced from decomposition of cellulose. Olefins are produced from the interaction reaction (carbenium ion reaction and beta-scission) between the primary products of cellulose and the hydrocarbon pool reaction of primary products of cellulose and PP. The results of this study enhance the understanding of co-pyrolysis of cellulose and PP in the presence of MCM-41 and provide the possible pathway of modifying the special pyrolysis products in catalytic pyrolysis of biomass with polymers.
Synergistic Effects on Char and Oil Produced by the Co-Pyrolysis of Pine Wood, Polyethylene and Polyvinyl Chloride

Peng Lu,Qunxing Huang,A. C. (Thanos) Bourtsalas,Yong Chi,Jianhua Yan

DOI: https://doi.org/10.1016/j.fuel.2018.05.072

IF: 7.4

2018-01-01

Fuel

Abstract:The synergistic effects of the woody biomass (pine wood (PW)) and plastics (polyethylene (PE) and polyvinyl chloride (PVC)) during co-pyrolysis on the properties of char and oil were examined by thermogravimetric analysis (TGA) and fixed bed reactor. The results showed that PW-PE interaction increased the maximum weight loss rate of PW by 8.0-23.7%. Co-pyrolysis of PW-PE blends produced lower quantity of char (13.8-22.4%) and higher quantity of oil (3.7-4.4%) as compared to the theoretical results. PW-PVC interaction decreased the temperature corresponding to the maximum weight loss rate of PW by 47-51 degrees C. Co-pyrolysis of PW-PVC blends yielded more char (15.5-27.9%) and less oil (7.2-14.4%) than expected values. Also, the interaction of biomass and plastic materials decreased the H/C atomic ratio of char, which resulted in a higher chemical stability of char. The fuel quality of oil produced from mixtures was improved due to a lower O/C atomic ratio of oil as compared to the theoretical results.
Synergistic effects from co-pyrolysis of lignocellulosic biomass main component with low-rank coal: Online and offline analysis on products distribution and kinetic characteristics

Zhiqiang Wu,Jie Zhang,Bo Zhang,Wei Guo,Guidong Yang,Bolun Yang

DOI: https://doi.org/10.1016/j.apenergy.2020.115461

IF: 11.2

2020-10-01

Applied Energy

Abstract:To comprehensively understanding the synergistic effects from co-pyrolysis of cellulose and low-rank coal, product distribution and kinetic characteristics were investigated based on both online and offline models. Thermogravimetric analysis combined with differential scanning calorimetry (DSC) and tubular furnace combined with online mass spectrometer were applied to investigate the synergistic effects from product distribution under slow and fast co-pyrolysis process, respectively. The model-free method and iso-conversion method were used for analyzing the synergistic interactions of kinetic characteristics. The results indicated that positive synergy from volatile products and kinetic behavior were observed from the slow co-pyrolysis with 50 wt% and 75 wt% of cellulose, with the lowest activation energy of 244.44 kJ·mol−1 and 164.41 kJ·mol−1, respectively. Thermal effect analysis from DSC indicated that the endothermic interval of cellulose was corresponding with the synergy interactions. For the fast co-pyrolysis process, both the temperature and the mass ratio of cellulose influenced the synergistic effect. Cellulose inhibited the formation of gaseous products and promoted the formation of tar. A negative synergistic effect was observed from the formation of CH4 and H2. The activation energy for the generation of CH4 and H2 from the mixture was higher than that of cellulose or low-rank coal alone. The results could provide some guidance for selecting proper reaction conditions with the optimal synergy during co-pyrolysis process.

energy & fuels,engineering, chemical
Co-pyrolysis characteristics and synergistic mechanism of low-rank coal and direct liquefaction residue

Yonghui Song,Ning Yin,Di Yao,Qiaona Ma,Jun Zhou,Xinzhe Lan

DOI: https://doi.org/10.1080/15567036.2019.1568639

2019-02-06

Abstract:In this study, the co-pyrolysis of low-rank pulverized coal (SJC) and direct liquefaction residue (DCLR) was comparatively examined. The structure and composition of tar and the evolution characteristics of gas during pyrolysis were analyzed through GC-MS, TG-FTIR, and other analytic techniques. Results showed that SJC+DCLR co-pyrolysis exhibited a significant synergistic effect. SJC and DCLR served as hydrogen donors to facilitate the hydrogenation of small molecular free radical fragments through pyrolysis, which increased the tar yield by 5.55%. Aromatic hydrocarbon and phenol contents in tar decreased by 11.88% and 7.94%, respectively, and alkane content increased by 12.25%. H2 content in gas decreased by 19.05%, and CH4 content increased by 19.60%. Co-pyrolysis could be divided into three stages. In the first stage, adsorbed water and CO2 were removed at room temperature to 344.91°C, and the weak chemical bond between SJC and DCLR began to break. In the second stage, SJC and DCLR became pyrolyzed, small molecular free radical fragments were hydrogenated, large amounts of tar and small-molecule gases were produced at 344.91–643.35°C, and synergistic effect was primarily observed. In the third stage, condensation reaction occurred between small molecular free radical fragments at 643.35–845.75°C, thereby producing solid coke and a small amount of gas.
Co-pyrolysis of Oily Sludge and Rice Husk for Improving Pyrolysis Oil Quality

Bingcheng Lin,Qunxing Huang,Yong Chi

DOI: https://doi.org/10.1016/j.fuproc.2018.05.002

IF: 8.129

2018-01-01

Fuel Processing Technology

Abstract:Co-pyrolysis of oily sludge and rice husk was conducted in a fixed-bed reactor to investigate the effects of interactions on the products and improve the quality of the pyrolysis oil. The synergy can be attributed to the catalytic effects of ash and alkali metals derived from biomass. SARA results showed that synergy enhanced the quality of oil product by promoting the content of saturates and aromatics and reducing heavy fractions. Gas chromatography/mass spectrometry results showed that the interaction increased the concentration of chain hydrocarbons and significantly reduced the content of oxygenated compounds by 46–93%. The gas yield was improved due to the promotion of secondary reactions and more H2, CO and C1–C2 hydrocarbons were generated. Additionally, though the emission of H2S was restrained, the distribution of sulfur in oil and gas phases was promoted.

[The effect of cefoxitin for surgical infections. Especially, the effect for resisted cases to therapy with another cephalosporins (author's transl)].

In-depth Study of Synergism Between Torrefaction and Catalyst for Balanced Production of Bio-Oil from Rice Husk Pyrolysis Based on Hydrocarbons Production, Energy Yield and Deoxygenation Degree

Co-pyrolysis of sewage sludge and lignocellulosic biomass: Synergistic effects on products characteristics and kinetics

Thermogravimetric characteristics of corn straw and bituminous coal co-pyrolysis based the ilmenite oxygen carriers

Synergistic effects, gas evolution and ash interaction during isothermal steam co-gasification of biomass with high-sulfur petroleum coke

Experimental study on co-pyrolysis of petroleum coke and coals: Synergy effects and co-gasification reactivity

Synergistic effect of co-pyrolysis of tea seed shells and scrap tyres and product evaluation

Thermogravimetric-infrared analysis and performance optimization of co-pyrolysis of oily sludge and rice husks

Synergistic effect on thermal behavior and product characteristics during co-pyrolysis of biomass and waste tire: Influence of biomass species and waste blending ratios

Infrared heating and synergistic effects during fast co-pyrolysis of corn stover and high alkali coal

Synergistic effect of Hami coal and polystyrene on products properties during co-pyrolysis: Evaluation on the contribution of different interaction sources

Co-pyrolysis of low-rank coal and rice stalk: A comprehensive study on product distributions, product properties, and synergistic effects

A TG-IR study on the co-pyrolysis characteristics of oily sludge and crops

Co-pyrolysis of different torrefied Chinese herb residues and low-density polyethylene: Kinetic and products distribution

Physicochemical synergistic effect of microwave-assisted Co-pyrolysis of biomass and waste plastics by thermal degradation, thermodynamics, numerical simulation, kinetics, and products analysis

Investigation on the characteristics and interaction of co-pyrolysis of oil shale and peanut shell

Synergetic Effect of Co-pyrolysis of Cellulose and Polypropylene over an All-Silica Mesoporous Catalyst MCM-41 Using Thermogravimetry–Fourier Transform Infrared Spectroscopy and Pyrolysis–Gas Chromatography–Mass Spectrometry

Synergistic Effects on Char and Oil Produced by the Co-Pyrolysis of Pine Wood, Polyethylene and Polyvinyl Chloride

Synergistic effects from co-pyrolysis of lignocellulosic biomass main component with low-rank coal: Online and offline analysis on products distribution and kinetic characteristics

Co-pyrolysis characteristics and synergistic mechanism of low-rank coal and direct liquefaction residue

Co-pyrolysis of Oily Sludge and Rice Husk for Improving Pyrolysis Oil Quality