Abstract:CO2 capture via physical adsorption on activated porous carbons represents a promising solution towards effective carbon emission mitigation. Additionally, production costs can be further decreased by utilising biomass as the main precursor and applying energy-efficient activation. In this work, we developed novel cellulose-based activated carbons modified with amines (diethylenetriamine (DETA), 1,2-bis(3-aminopropylamino)ethane (BAPE), and melamine (MELA)) with different numbers of nitrogen atoms as in situ N-doping precursors. We investigated the effect of hydrothermal and thermal activation on the development of their physicochemical properties, which significantly influence the resulting CO2 adsorption capacity. This process entailed an initial hydrothermal activation of biomass precursor and amines at 240 °C, resulting in C+DETA, C+BAPE and C+MELA materials. Thermal samples (C+DETA (P), C+BAPE (P), and C+MELA (P)) were synthesised from hydrothermal materials by subsequent KOH chemical activation and pyrolysis in an inert argon atmosphere. Their chemical and structural properties were characterised using elemental analysis (CHN), infrared spectroscopy (IR), scanning electron microscopy (SEM), and thermogravimetric analysis (TG). The calculated specific surface areas (SBET) for thermal products showed higher values (998 m2 g−1 for C+DETA (P), 1076 m2 g−1 for C+BAPE (P), and 1348 m2 g−1 for C+MELA (P)) compared to the hydrothermal products (769 m2 g−1 for C+DETA, 833 m2 g−1 for C+BAPE, and 1079 m2 g−1 for C+MELA). Carbon dioxide adsorption as measured by volumetric and gravimetric methods at 0 and 25 °C, respectively, showed the opposite trend, which can be attributed to the reduced content of primary adsorption sites in the form of amine groups in thermal products. N2 and CO2 adsorption measurements were carried out on hydrothermal (C) and pyrolysed cellulose (C (P)), which showed a several-fold reduction in adsorption properties compared to amine-modified materials. The recyclability of C+MELA, which showed the highest CO2 adsorption capacity (7.34 mmol g−1), was studied using argon purging and thermal regeneration over five adsorption/desorption cycles.

Exploring the structural characteristics and adsorption capabilities of cost-effective N- doped activated carbon derived from waste biomass for CO2 adsorption

An Efficient Biochar Adsorbent for CO2 Capture: Combined Experimental and Theoretical Study on the Promotion Mechanism of N-doping

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

Synthesis and characterization of activated carbon from biomass date seeds for carbon dioxide adsorption

Systematic study of dynamic CO2 adsorption on activated carbons derived from different biomass

Preparation of Nitrogen-Doped Activated Carbon from Bio-Oil Residue for Efficient CO2 Adsorption

Experimental Study and Thermodynamic Analysis of Carbon Dioxide Adsorption onto Activated Carbons Prepared from Biowaste Raw Materials

Freundlich, Langmuir, Temkin, DR and Harkins-Jura Isotherm Studies on the Adsorption of CO2 on Various Porous Adsorbents

Tailoring tea residue-derived nitrogen-doped activated carbon for CO2 adsorption: influence of activation temperature and activating agents

Designing microporous activated carbons from biomass for carbon dioxide adsorption at ambient temperature. A comparison between bagasse and rice by-products

The development of activated carbon from corncob for CO2 capture

N-doped porous carbon derived from macadamia nut shell for CO 2 adsorption

The effect of humidity on the enhanced CO2 adsorption of amine-functionalized microporous activated carbon

The fabrication of porous N-doped carbon from widely available urea formaldehyde resin for carbon dioxide adsorption

Porous activated carbons derived from waste sugarcane bagasse for CO2 adsorption

High-value utilization of lignin to prepare N,O-codoped porous carbon as a high-performance adsorbent for carbon dioxide capture

Performance of CO2 Adsorption on Modified Activated Carbons Derived from Okara Powder Waste: Impacts of Ammonia Impregnation

One-Pot Synthesis of N-Rich Porous Carbon for Efficient CO2 Adsorption Performance

Cellulose–Amine Porous Materials: The Effect of Activation Method on Structure, Textural Properties, CO2 Capture, and Recyclability

Nitrogen configuration enriched N-doped activated carbon from spent tea leaves through an ammonia impregnation approach for CO 2 adsorption

Enhancing graphitization with desirable porosity for CO 2 adsorption through a one-step strategy and a novel stepwise pyrolysis method from Terminalia boivinii tul tree dead leaves